- 您現在的位置：買賣IC網 > PDF目錄296205 > ICS9248YF-153-T (INTEGRATED DEVICE TECHNOLOGY INC) 133.33 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 PDF資料下載
參數資料
| 型號： | ICS9248YF-153-T |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | XO, clock |
| 英文描述： | 133.33 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| 封裝： | 0.300 INCH, SSOP-48 |
| 文件頁數： | 2/14頁 |
| 文件大?。?/td> | 293K |
| 代理商： | ICS9248YF-153-T |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
10
ICS9248-153
Third party brands and names are the property of their respective owners.
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS9248-
153 serve as dual signal functions to the device. During initial
power-up, they act as input pins. The logic level (voltage)
that is present on these pins at this time is read and stored
into a 5-bit internal data latch. At the end of Power-On reset,
(seeAC characteristics for timing values), the device changes
the mode of operations for these pins to an output function.
In this mode the pins produce the specified buffered clocks
to external loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm
(10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function when
a switch or 2 pin header is used. With no jumper is installed
the pin will be pulled high. With the jumper in place the pin
will be pulled low. If programmability is not necessary, than
only a single resistor is necessary. The programming resistors
should be located close to the series termination resistor to
minimize the current loop area. It is more important to locate
the series termination resistor close to the driver than the
programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS950218YF-T-LF | 200.4 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
| ICS950805YF-T | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS950805YFLF-T | 200 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS950905YFLFT | 200.4 MHz, OTHER CLOCK GENERATOR, PDSO48 |
| ICS951704YFLFT | 166 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS9248YF-157-T | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Timing Generator for Pentium II Systems |
| ICS9248YF-163-T | 制造商:ICS 制造商全稱:ICS 功能描述:AMD - K7⑩ System Clock Chip |
| ICS9248YF-168-T | 制造商:ICS 制造商全稱:ICS 功能描述:AMD - K7⑩ Clock Generator for Mobile System |
| ICS9248YF-171-T | 制造商:ICS 制造商全稱:ICS 功能描述:AMD - K7TM System Clock Chip |
| ICS9248YF-189-T | 制造商:ICS 制造商全稱:ICS 功能描述:AMD - K7⑩ Clock Generator for Mobile System |
發布緊急采購，3分鐘左右您將得到回復。