- 您現在的位置：買賣IC網 > PDF目錄370795 > HYE25L256160AF-7.5 (INFINEON TECHNOLOGIES AG) BJAWBMSpecialty DRAMs Mobile-RAM PDF資料下載
參數資料
| 型號： | HYE25L256160AF-7.5 |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | BJAWBMSpecialty DRAMs Mobile-RAM |
| 中文描述： | BJAWBMSpecialty DRAM的移動RAM |
| 文件頁數： | 10/55頁 |
| 文件大小： | 1053K |
| 代理商： | HYE25L256160AF-7.5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
HYE25L256160AC
256-Mbit Mobile-RAM
Functional Description
Data Sheet
10
V1.1, 2003-04-16
3
Functional Description
The 256-Mbit Mobile-RAM is a new generation of low power, four bank synchronous DRAM organized as
4 banks
×
4 Mbit
×
16 with additional features for mobile applications. The synchronous Mobile-RAM achieves
high speed data transfer rates by employing a chip architecture that prefetches multiple bits and then synchronizes
the output data to a system clock.
The device adds new features to the industry standards set for synchronous DRAM products. Parts of the memory
array can be selected for Self-Refresh and the refresh period during Self-Refresh is programmable in 4 steps
which drastically reduces the self refresh current, depending on the case temperature of the components in the
system application. In addition a “Deep Power Down Mode” is available. Operating the four memory banks in an
interleave fashion allows random access operation to occur at higher rate. A sequential and gapless data rate is
possible depending on burst length, CAS latency and speed grade of the device.
Prior to normal operation, the 256-Mbit Mobile-RAM must be initialized. The following sections provide detailed
information covering device initialization, register definition, command descriptions and device operation.
3.1
Initialization
The default power on state of the mode register is supplier specific and may be undefined. The following power
on and initialization sequence guarantees the device is preconditioned to each users specific needs. Like a
conventional DRAM, the 256-Mbit Mobile-RAM must be powered up and initialized in a predefined manner.
V
DD
must be applied before or at the same time as
V
DDQ
to the specified voltage when the input signals are held in the
“NOP” or “DESELECT” state. The power on voltage must not exceed
V
DD
+ 0.3 V on any of the input pins or
V
DDQ
supplies. The CLK signal must be started at the same time. After power on, an initial pause of 200 ms is required
followed by a precharge of all banks using the precharge command. To prevent data contention on the DQ bus
during power on, it is required that the DQM and CKE pins be held high during the initial pause period. Once all
banks have been precharged, the Mode Register Set Command must be issued to initialize the Mode Register.
A minimum of eight Auto Refresh cycles (CBR) are also required.These may be done before or after programming
the Mode Register. Failure to follow these steps may lead to unpredictable start-up modes.Mode Register
Definition
3.2
Mode Register
The Mode Register designates the operation mode at the read or write cycle. This register is divided into four
fields. A Burst Length Field to set the length of the burst, an Addressing Selection bit to program the column access
sequence in a burst cycle (interleaved or sequential), and a CAS Latency Field to set the access time at clock
cycle, an The mode set operation must be done before any activate command after the initial power up. Any
content of the mode register can be altered by re-executing the mode set command. All banks must be in
precharged state and CKE must be high at least one clock before the mode set operation. After the mode register
is set, a Standby or NOP command is required. Low signals of RAS, CAS, and WE at the positive edge of the clock
activate the mode set operation. Address input data at this timing defines parameters to be set as shown in the
previous table. BA0 and BA1 have to be set to “0” to enter the Mode Register.
相關PDF資料 |
PDF描述 |
|---|---|
| HYE25L256160AC | 256-Mbit Mobile-RAM |
| HYE25L256160AC-8 | 256-Mbit Mobile-RAM |
| HYE25L256160AF | 256MBit Mobile-RAM |
| HYE25L256160AF-75 | CAP TANT 10UF 6.3V 20% SMD |
| HYE25L256160AC-7.5 | BJAWBMSpecialty DRAMs Mobile-RAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HYESD0514P | 制造商:HY 制造商全稱:HY ELECTRONIC CORP. 功能描述:4 Channel Low Capacitance ESD Protection Diode Array |
| HYESD0524A6 | 制造商:HY 制造商全稱:HY ELECTRONIC CORP. 功能描述:4 Channel Low Capacitance ESD Protection Diode Array |
| HYESD0524P | 制造商:HY 制造商全稱:HY ELECTRONIC CORP. 功能描述:4 Channel Low Capacitance ESD Protection Diode Array |
| HYESD1025QG | 制造商:HY 制造商全稱:HY ELECTRONIC CORP. 功能描述:2 Channel Low Capacitance ESD Protection DIode Array |
| HYESD1065M | 制造商:HY 制造商全稱:HY ELECTRONIC CORP. 功能描述:6 Channel Low Capacitance ESD Protection Diode Array |
發布緊急采購，3分鐘左右您將得到回復。