參數資料
型號： HYE18P32161AC-85
廠商： INFINEON TECHNOLOGIES AG
英文描述： 32M Asynchronous/Page CellularRAM
中文描述： 32M的異步/頁的CellularRAM
文件頁數： 13/33頁
文件大小： 641K
代理商： HYE18P32161AC-85
Data Sheet
13
V2.0, 2003-12-16
HYE18P32161AC(-/L)70/85
32M Asynch/Page CellularRAM
Overview
1.6
Commands
All commands are of asynchronous nature. The supported control signal combinations are listed in the table below.
C
Table 3
Note:‘L’ represents a low voltage level, ‘H’ a high voltage level, ‘X’ represents “Don’t Care”, ‘V’ represents “Valid”.
Note:‘L’ represents a low voltage level, ‘H’ a high voltage level, ‘X’ represents “Don’t Care”, ‘V’ represents “Valid”.
Asynchronous Command Table
Operation Mode
READ
WRITE
SET CONTROL
REGISTER
NO OPERATION
DESELECT
DPD
Power Mode
Active
Active
Active
CS1
L
L
L
WE
H
L
L
OE
L
X
2)
X
2)
UB/LB
L
1)
L
1)
X
ZZ
H
H
L
A19
V
V
L
A20 - A0
ADR
ADR
RCR DIN
DQ15:0
DOUT
DIN
X
1)
Table 3
reflects the behaviour if UB and LB are asserted to low. If only either of the signals, UB or LB, is asserted to low
only the corresponding data byte will be output or written (UB enables DQ15 - DQ8, LB enables DQ7 - DQ0).
2) During a write access invoked by WE set to low the OE signal is ignored.
3) Stand-by power mode applies only to the case when CS goes low from DESELECT while no address change occurs.
Toggling address results in active power mode. Also, NO OPERATION from any active power mode by keeping CS low
consumes the power higher than stand-by mode.
Standby~Active
3)
Standby
Deep Power Down
L
H
H
H
X
X
H
X
X
X
X
X
H
X
L
X
X
X
X
X
X
High-Z
High-Z
High-Z
Table 4
Mode
READ
Description of Commands
Description
The READ command is used to perform an asynchronous read cycle. The
signals, UB and LB, define whether only the lower, the upper or the whole 16-bit
word is output.
The WRITE command is used to perform an asynchronous write cycle. The data
is latched on the rising edge of either CS, WE, UB, LB, whichever comes first.
The signals, UB and LB, define whether only the lower, the upper or the whole
16-bit word is latched into the CellularRAM.
The control registers are loaded via the address inputs A15 - A0 performing an
asynchronous write access. Please refer to the control register description for
details. The SCR command can only be issued when the CellularRAM is in idle
state.
The NOP command is used to perform a no operation to the CellularRAM, which
is selected (CS1 = 0). Operations already in progress are not affected. Power
consumption of this command mode varies by address change and initiating
condition.
The DESELECT function prevents new commands from being executed by the
CellularRAM. The CellularRAM is effectively deselected. I/O signals are put to
high impedance state.
DPD stops all refresh-related activities and entire on-chip circuit operation.
Current consumption drops below 25
μ
A. Wake-up from DPD also requires
150
μ
s to get ready for normal operation.
WRITE
SET CONTROL REGISTER
NO OPERATION
DESELECT
DPD
相關PDF資料
PDF描述
HYE18P32161AC 32M Asynchronous/Page CellularRAM
HYE18P32161ACL70 JT 23C 21#20 2#16 SKT PLUG
HYE18P32161ACL85 Circular Connector; MIL SPEC:MIL-DTL-38999 Series II; Body Material:Metal; Series:JT; No. of Contacts:11; Connector Shell Size:18; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No
HYE18P32161AC-70 32M Asynchronous/Page CellularRAM
HYE25L256160AC-75 SMP(M)PIN CONT,PCB REAR MNT
相關代理商/技術參數
參數描述
HYE18P32161ACL70 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:32M Asynchronous/Page CellularRAM
HYE18P32161ACL85 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:32M Asynchronous/Page CellularRAM
HYE25L128160AC-7.5 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:BJAWBMSpecialty DRAMs Mobile-RAM
HYE25L128160AC-75 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:128-MBIT SYNCHRONOUS LOW-POWER DRAM IN CHIPSIZE PACKAGES
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*