- 您現在的位置：買賣IC網 > PDF目錄385426 > HY5DU281622ET-26 (HYNIX SEMICONDUCTOR INC) 128M(8Mx16) GDDR SDRAM PDF資料下載
參數資料
| 型號： | HY5DU281622ET-26 |
| 廠商： | HYNIX SEMICONDUCTOR INC |
| 元件分類： | DRAM |
| 英文描述： | 128M(8Mx16) GDDR SDRAM |
| 中文描述： | 8M X 16 DDR DRAM, 0.6 ns, PDSO66 |
| 封裝： | 0.400 X 0.875 INCH, 0.65 MM PITCH, TSOP2-66 |
| 文件頁數： | 7/34頁 |
| 文件大?。?/td> | 379K |
| 代理商： | HY5DU281622ET-26 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Rev. 0.5 / Jan. 2005
7
HY5DU281622ET
SIMPLIFIED COMMAND TRUTH TABLE
Command
CKEn-1
CKEn
CS
RAS
CAS
WE
ADDR
A10/
AP
BA
Note
Extended Mode Register Set
H
X
L
L
L
L
OP code
1,2
Mode Register Set
H
X
L
L
L
L
OP code
1,2
Device Deselect
H
X
H
X
X
X
X
1
No Operation
L
H
H
H
Bank Active
H
X
L
L
H
H
RA
V
1
Read
H
X
L
H
L
H
CA
L
V
1
Read with Autoprecharge
H
1,3
Write
H
X
L
H
L
L
CA
L
V
1
Write with Autoprecharge
H
1,4
Precharge All Banks
H
X
L
L
H
L
X
H
X
1,5
Precharge selected Bank
L
V
1
Read Burst Stop
H
X
L
H
H
L
X
1
Auto Refresh
H
H
L
L
L
H
X
1
Self Refresh
Entry
H
L
L
L
L
H
X
1
Exit
L
H
H
X
X
X
1
L
H
H
H
Precharge Power
Down Mode
Entry
H
L
H
X
X
X
X
1
L
H
H
H
1
Exit
L
H
H
X
X
X
1
L
H
H
H
1
Active Power
Down Mode
Entry
H
L
H
X
X
X
X
1
L
V
V
V
1
Exit
L
H
X
1
Note :
1. UDM, LDM states are Don’t Care. Refer to below Write Mask Truth Table.(note 6)
2. OP Code(Operand Code) consists of A0~A11 and BA0~BA1 used for Mode Register setting during Extended MRS or MRS. Before
entering Mode Register Set mode, all banks must be in a precharge state and MRS command can be issued after tRP period from
Prechagre command.
3. If a Read with Auto-precharge command is detected by memory component in CK(n), then there will be no command presented
to activate bank until CK(n+BL/2+tRP).
4. If a Write with Auto-precharge command is detected by memory component in CK(n), then there will be no command presented
to activate bank until CK(n+BL/2+1+tDPL+tRP). Last Data-In to Prechage delay(tDPL) which is also called Write Recovery
Time(tWR) is needed to guarantee that the last data have been completely written.
5. If A10/AP is High when Precharge command being issued, BA0/BA1 are ignored and all banks are selected to be precharged.
6. In here, Don’t Care means logical value only, it doesn’t mean ’Don’t care for DC level of each signals’. DC level should be out of
V
IHmin
~ V
ILmax
( H=Logic High Level, L=Logic Low Level, X=Don’t Care, V=Valid Data Input, OP Code=Operand Code, NOP=No Operation )
相關PDF資料 |
PDF描述 |
|---|---|
| HY5DU281622ET-28 | 128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-30 | 128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-33 | 128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-36 | 128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-4 | 128M(8Mx16) GDDR SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HY5DU281622ET-28 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-30 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-33 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-36 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:128M(8Mx16) GDDR SDRAM |
| HY5DU281622ET-4 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:128M(8Mx16) GDDR SDRAM |
發布緊急采購，3分鐘左右您將得到回復。