- 您現在的位置：買賣IC網 > PDF目錄370461 > HD404849FS (Hitachi,Ltd.) TERMINAL PDF資料下載
參數資料
| 型號： | HD404849FS |
| 廠商： | Hitachi,Ltd. |
| 元件分類： | 其它接口 |
| 英文描述： | TERMINAL |
| 中文描述： | IGBT模塊 |
| 文件頁數： | 19/125頁 |
| 文件大小： | 471K |
| 代理商： | HD404849FS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁
HD404849 Series
19
Interrupts
The MCU has ten interrupt sources: four external signals (
INT
0
,
INT
1
,
INT
2
, INT
3
), four timer/counters
(timers A, B, C, and D), serial interface, and A/D converter.
An interrupt request flag (IF), interrupt mask (IM), and vector address are provided for each interrupt
source, and an interrupt enable flag (IE) controls the entire interrupt process.
Some vector addresses are shared by two different interrupts. They are timer B and INT
2
, timer C and
INT
3
, and A/D converter and serial interface interrupts. So the type of request that has occurred must be
checked at the beginning of interrupt processing.
Interrupt Control Bits and Interrupt Processing:
Locations $000 to $003 and $022 to $023 in RAM are
reserved for the interrupt control bits which can be accessed by RAM bit manipulation instructions.
The interrupt request flag (IF) cannot be set by software. MCU reset initializes the interrupt enable flag
(IE) and the IF to 0 and the interrupt mask (IM) to 1.
A block diagram of the interrupt control circuit is shown in figure 9, interrupt priorities and vector
addresses are listed in table 2, and interrupt processing conditions for the ten interrupt sources are listed in
table 3.
An interrupt request occurs when the IF is set to 1 and the IM is set to 0. If the IE is 1 at that point, the
interrupt is processed. A priority programmable logic array (PLA) generates the vector address assigned to
that interrupt source.
The interrupt processing sequence is shown in figure 10 and an interrupt processing flowchart is shown in
figure 11. After an interrupt is acknowledged, the previous instruction is completed in the first cycle. The
IE is reset in the second cycle, the carry, status, and program counter values are pushed onto the stack
during the second and third cycles, and the program jumps to the vector address to execute the instruction
in the third cycle.
Program the JMPL instruction at each vector address, to branch the program to the start address of the
interrupt program, and reset the IF by a software instruction within the interrupt program.
Table 2 Vector Addresses and Interrupt Priorities
Reset/Interrupt
RESET
,
STOPC
*
INT
0
INT
1
Timer A
Timer B, INT
2
Timer C, INT
3
Timer D
A/D, Serial
Note:
*
The
STOPC
interrupt request is valid only in stop mode.
Priority
—
1
2
3
4
5
6
7
Vector Address
$0000
$0002
$0004
$0006
$0008
$000A
$000C
$000E
相關PDF資料 |
PDF描述 |
|---|---|
| HD404849H | SPLICE |
| HD404849TF | TERMINAL |
| HD4074849 | TERMINAL |
| HD4074849FS | CONTACT |
| HD4074849H | CONTACT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD404849H | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-Bit Single-Chip Microcomputer |
| HD404849SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| HD404849TF | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:4-Bit Single-Chip Microcomputer |
| HD404868 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit |
| HD404878 | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit |
發布緊急采購，3分鐘左右您將得到回復。