參數資料
型號： HCPL-316J
英文描述： 2.0 Amp Gate Drive Optocoupler with Integrated (V CE ) Desaturation Detection and Fault Status Feedback(帶集成不飽和檢測和誤差反饋的2.0 Amp門驅動耦合器)
中文描述： 2.0安培門極驅動光電耦合器與集成（五長官）飽和檢測與故障狀態反饋（帶集成不飽和檢測和誤差反饋的2.0安培門驅動耦合器）
文件頁數： 20/32頁
文件大?。?/td> 503K
代理商： HCPL-316J
20
Typical Application/
Operation
Introduction to Fault
Detection and Protection
The power stage of a typical three
phase inverter is susceptible to
several types of failures, most of
which are potentially destructive
to the power IGBTs. These failure
modes can be grouped into four
basic categories: phase and/or
rail supply short circuits due to
user misconnect or bad wiring,
control signal failures due to
noise or computational errors,
overload conditions induced by
the load, and component failures
in the gate drive circuitry. Under
any of these fault conditions, the
current through the IGBTs can
increase rapidly, causing
excessive power dissipation and
heating. The IGBTs become
damaged when the current load
approaches the saturation current
of the device, and the collector to
emitter voltage rises above the
saturation voltage level. The
drastically increased power
dissipation very quickly overheats
the power device and destroys it.
To prevent damage to the drive,
fault protection must be
implemented to reduce or
turn-off the overcurrents during a
fault condition.
A circuit providing fast local fault
detection and shutdown is an
ideal solution, but the number of
required components, board
space consumed, cost, and
complexity have until now limited
its use to high performance
drives. The features which this
circuit must have are high speed,
low cost, low resolution, low
power dissipation, and small size.
The HCPL-316J satisfies these
criteria by combining a high
speed, high output current driver,
high voltage optical isolation
between the input and output,
local IGBT desaturation detection
and shut down, and an optically
isolated fault status feedback
signal into a single 16-pin surface
mount package.
The fault detection method,
which is adopted in the
HCPL-316J, is to monitor the
saturation (collector) voltage of
the IGBT and to trigger a local
fault shutdown sequence if the
collector voltage exceeds a
predetermined threshold. A small
gate discharge device slowly
reduces the high short circuit
IGBT current to prevent
damaging voltage spikes. Before
the dissipated energy can reach
destructive levels, the IGBT is
shut off. During the off state of
the IGBT, the fault detect
circuitry is simply disabled to
prevent false ‘fault’ signals.
The alternative protection
scheme of measuring IGBT
current to prevent desaturation is
effective if the short circuit
capability of the power device is
known, but this method will fail if
the gate drive voltage decreases
enough to only partially turn on
the IGBT. By directly measuring
the collector voltage, the
HCPL-316J limits the power
dissipation in the IGBT even with
insufficient gate drive voltage.
Another more subtle advantage of
the desaturation detection
method is that power dissipation
in the IGBT is monitored, while
the current sense method relies
on a preset current threshold to
predict the safe limit of
operation. Therefore, an overly-
conservative overcurrent
threshold is not needed to protect
the IGBT.
Recommended Application
Circuit
The HCPL-316J has both
inverting and non-inverting gate
control inputs, an active low reset
input, and an open collector fault
output suitable for wired ‘OR’
applications. The recommended
application circuit shown in
Figure 62 illustrates a typical
gate drive implementation using
the HCPL-316J.
The four supply bypass
capacitors (0.1
μ
F) provide the
large transient currents necessary
during a switching transition.
Because of the transient nature of
the charging currents, a low
current (5 mA) power supply
suffices. The desat diode and 100
pF capacitor are the necessary
external components for the fault
detection circuitry. The gate
resistor (10
) serves to limit
gate charge current and indirectly
control the IGBT collector
voltage rise and fall times. The
open collector fault output has a
passive 3.3 k
pull-up resistor
and a 330 pF filtering capacitor.
A 47 k
pulldown resistor on
V
OUT
provides a more predictable
high level output voltage (V
OH
).
In this application, the IGBT gate
driver will shut down when a fault
is detected and will not resume
switching until the
microcontroller applies a reset
signal.
Applications Information
相關PDF資料
PDF描述
HCPL-3700 AC/DC to Logic Interface Optocouplers(AC/DC邏輯接口光耦合器)
HCPL-4100300 Optically Coupled 20 mA Current Loop Transmitter
HCPL-4100500 Optically Coupled 20 mA Current Loop Transmitter
HCPL4100 Optically Coupled 20 mA Current Loop Transmitter
HCPL-4100 Optically Coupled 20 mA Optically Coupled 20 mA
相關代理商/技術參數
參數描述
HCPL-316J#500 功能描述:邏輯輸出光電耦合器 2.0A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-316J-000E 功能描述:邏輯輸出光電耦合器 2.0A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-316J-000E 制造商:Avago Technologies 功能描述:GATE DRIVE OPTOCOUPLERLF - LEAD FREE VE
HCPL-316J-500E 功能描述:邏輯輸出光電耦合器 2.0A IGBT Gate Drive RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
HCPL-3180 功能描述:高速光耦合器 2.0A IGBT Gate Drive RoHS:否 制造商:Avago Technologies 電流傳遞比: 最大波特率: 最大正向二極管電壓:1.75 V 最大反向二極管電壓:5 V 最大功率耗散:40 mW 最大工作溫度:+125 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-5 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*