參數資料
型號： HCD404669
廠商： Hitachi,Ltd.
英文描述： Low-Voltage AS Microcomputers with On-Chip DTMF Generation Circuit(帶雙音多頻電路的低電壓微計算機)
中文描述： 低電壓如同在微機芯片的DTMF產生電路（帶雙音多頻電路的低電壓微計算機）
文件頁數： 23/142頁
文件大?。?/td> 894K
代理商： HCD404669
HD404669 Series
23
Interrupts
The MCU has 9 interrupt sources: five external signals (
INT
0
,
INT
1
, INT
2
–INT
4
), three timer/ counters
(timers A, C, and D), serial interface (Serial 1).
An interrupt request flag (IF), interrupt mask (IM), and vector address are provided for each interrupt
source, and an interrupt enable flag (IE) controls the entire interrupt process.
As vector addresses are shared by interrupt sources timer C and INT
3
, and timer D and INT
4
, so the type of
request that has occurred must be checked at the beginning of interrupt processing.
Interrupt Control Bits and Interrupt Processing:
Locations $000 to $003 and $022 to $023 in RAM are
reserved for the interrupt control bits which can be accessed by RAM bit manipulation instructions.
The interrupt request flag (IF) cannot be set by software. MCU reset initializes the interrupt enable flag
(IE) and the IF to 0 and the interrupt mask (IM) to 1.
A block diagram of the interrupt control circuit is shown in figure 9, interrupt priorities and vector
addresses are listed in table 2, and interrupt processing conditions for the 9 interrupt sources are listed in
table 3.
An interrupt request occurs when the IF is set to 1 and the IM is set to 0. If the IE is 1 at that point, the
interrupt is processed. A priority programmable logic array (PLA) generates the vector address assigned to
that interrupt source.
The interrupt processing sequence is shown in figure 10 and an interrupt processing flowchart is shown in
figure 11. After an interrupt is acknowledged, the previous instruction is completed in the first cycle. The
IE is reset in the second cycle, the carry, status, and program counter values are pushed onto the stack
during the second and third cycles, and the program jumps to the vector address to execute the instruction
in the third cycle.
Program the JMPL instruction at each vector address, to branch the program to the start address of the
interrupt program, and reset the IF by a software instruction within the interrupt program.
Table 2 Vector Addresses and Interrupt Priorities
Reset/Interrupt
RESET,
STOPC
*
INT
0
INT
1
Timer A
Priority
Vector Address
—
$0000
1
$0002
2
$0004
3
$0006
INT
2
Timer C, INT
3
Timer D, INT
4
Serial 1
Note:
4
$0008
5
$000A
6
$000C
7
$000E
*
The
STOPC
interrupt request is valid only in stop mode.
相關PDF資料
PDF描述
HCD404868 Low-Voltage AS Microcomputers with On-Chip LCD Circuit(片上LCD電路的低壓微計算機)
HCD404878 Low-Voltage AS Microcomputers with On-Chip LCD Circuit(片上LCD電路的低壓微計算機)
HCD404889 Low-Voltage AS Microcomputers with On-Chip LCD Circuit(片上LCD電路的低壓微計算機)
HCD404899 Low-Voltage AS Microcomputers with On-Chip LCD Circuit(片上LCD電路的低壓微計算機)
HCD40C4082 Low-Voltage AS Microcomputers with On-Chip A/D Converter(帶片上A/D轉換器的低壓微計算機)
相關代理商/技術參數
參數描述
HCD404889 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Low-Voltage AS Microcomputers with On-Chip LCD Circuit
HCD40C4344R 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-bit microcomputers
HCD44780UA00 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD44780UA02 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
HCD44780UBXX 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Dot Matrix Liquid Crystal Display Controller/Driver
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*