參數資料
型號: HC5515CMZ
廠商: Intersil
文件頁數: 19/20頁
文件大?。?/td> 0K
描述: IC SLIC ITU CO/PABX LP 28-PLCC
標準包裝: 925
功能: 用戶線路接口概念(SLIC)
電路數: 1
電源電壓: 4.75 V ~ 5.25 V
功率(瓦特): 1.5W
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 28-LCC(J 形引線)
供應商設備封裝: 28-PLCC(11.51x11.51)
包裝: 管件
包括: 可編程回路電流檢測器,振鈴?fù)禉z測器,熱關機
8
FN4235.6
June 6, 2006
Circuit Operation and Design Information
The HC5515 is a current feed voltage sense Subscriber Line
Interface Circuit (SLIC). This means that for short loop
applications the SLIC provides a programed constant current to
the tip and ring terminals while sensing the tip to ring voltage.
The following discussion separates the SLIC’s operation into
its DC and AC paths, then follows up with additional circuit
and design information.
Constant Loop Current (DC) Path
SLIC in the Active Mode
The DC path establishes a constant loop current that flows
out of tip and into the ring terminal. The loop current is
programmed by resistors RDC1, RDC2 and the voltage on
the RDC pin (Figure 12). The RDC voltage is determined by
the voltage across R1 in the saturation guard circuit. Under
constant current feed conditions, the voltage drop across R1
sets the RDC voltage to -2.5V. This occurs when current
flows through R1 into the current source I2. The RDC voltage
establishes a current (IRSN) that is equal to VRDC/(RDC1
+RDC2). This current is then multiplied by 1000, in the loop
current circuit, to become the tip and ring loop currents.
For the purpose of the following discussion, the saturation
guard voltage is defined as the maximum tip to ring voltage
at which the SLIC can provide a constant current for a given
battery and overhead voltage.
For loop resistances that result in a tip to ring voltage less than
the saturation guard voltage the loop current is defined as:
where: IL = Constant loop current, and
RDC1 and RDC2 = Loop current programming resistors.
Capacitor CDC between RDC1 and RDC2 removes the VF
signals from the battery feed control loop. The value of CDC
is determined by Equation 2:
where T = 30ms.
NOTE: The minimum CDC value is obtained if RDC1 = RDC2.
Figure 13 illustrates the relationship between the tip to ring
voltage and the loop resistance. For a 0
loop resistance
both tip and ring are at VBAT/2. As the loop resistance
increases, so does the voltage differential between tip and
ring. When this differential voltage becomes equal to the
saturation guard voltage, the operation of the SLIC’s loop
feed changes from a constant current feed to a resistive
feed. The loop current in the resistive feed region is no
longer constant but varies as a function of the loop
resistance.
VBAT to 2 or 4-Wire Port
(Note 29, Figure 11)
-
40
-
dB
FIGURE 11. POWER SUPPLY REJECTION RATIO
Electrical Specifications
TA = 0°C to 70°C, VCC = +5V ±5%, VEE = -5V ±5%, VBAT = -48V, AGND = BGND = 0V, RDC1 = RDC2 = 41.2k,
RD = 39k, RSG = 0, RF1 = RF2 = 0, CHP = 10nF, CDC = 1.5F, ZL = 600, Unless Otherwise Specified.
(Continued)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
RT
RRX
600k
300k
RL
VTX
600
100mVRMS, 50Hz TO 4kHz
-48V SUPPLY
+5V SUPPLY
-5V SUPPLY
PSRR = 20 log (VTX/VIN)
TIP
27
VTX
19
RING
28
RSN
16
I
L
2.5V
R
DC1
R
DC2
+
--------------------------------------
1000
×
=
(EQ. 1)
C
DC
T
1
R
DC1
---------------
1
R
DC2
---------------
+
×
=
(EQ. 2)
HC5515
相關PDF資料
PDF描述
HC9P5504B-5ZX96 IC SLIC EIA/ITU PABX 24-SOIC
HD3-6402R-9Z IC UART CMOS 5V 2MHZ 40-DIP
HD9P6409-9Z96 IC MED MANCHESTER 1MHZ 20-SOIC
HI1-0390-2 IC SWITCH DUAL SPDT 16CDIP
HI1-0524-5 IC VIDEO MULTIPLEXER 4X1 18CDIP
相關代理商/技術參數
參數描述
HC5515CP 制造商:Rochester Electronics LLC 功能描述:- Bulk
HC5515IM 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述:
HC5515IMR4717 制造商:Rochester Electronics LLC 功能描述:- Bulk
HC5515IP 制造商:Rochester Electronics LLC 功能描述:- Bulk
HC5515IP-5 制造商:Rochester Electronics LLC 功能描述:- Bulk