參數資料
型號： FMS9875KGC100
文件頁數： 2/29頁
文件大?。?/td> 481K
代理商： FMS9875KGC100
PRODUCT SPECIFICATION
FMS9875
2
REV. 1.2.15 1/14/02
Architectural Overview
Three separate digitizer channels are controlled by common
timing signals derived from the Timing Generator. A/D clock
signals can be derived from either a PLL or an external clock
XCK. With the PLL selected, A/D clocks track the incoming
horizontal sync signal connected to the HSIN input. Setup is
controlled by registers that are accessible through the serial
interface.
Conversion Channels
Typical RGB or YP
RPIN are ground referenced with 700mV amplitude. If a
sync signal is embedded then the usual format is sync on
green or Y with the sync tip at ground, the black level
elevated to 300mV and peak green at 1000mV. Either type
of input can be accepted by using the clamp function with
AC coupling.
B
P
R
input signals, GYIN, BPIN, and
Clamps
AC coupled input video signals must be level shifted to
match the signal and A/D converter reference levels during
the back porch (see Figure 1). Y/G inputs should be clamped
to the A/D converter lower reference level. P
should be clamped to the A/D converter midrange level
(nominally 350 mV), which is 50% of full scale (nominally
700 mV).
B
P
R
signals
Figure 1. Clamping to the back-porch
Clamp pulses, ICLAMP, are derived from internal Timing
and Control logic or from the external CLAMP input. Clamp
timing is common to the three input channels.
With the A/D range set to 700mV ground referenced, clamp
levels are:
RGB: 000mV
Y: 000mV
P
B
P
R
: +350mV
Clamp levels can be set through the registers or through the
YG
REF
, BP
REF
and RP
REF
pins.
Gain and Offset
Gain and Offset registers serve two functions: 1) Adjustment
of contrast and brightness by setting RGB values in tandems.
2) Matching the gain and offsets between channels, by
setting RGB values individually to obtain the same output
levels at zero and full-scale.
A/D conversion range can be matched to the amplitude of the
incoming video signal by programming Gain Registers
GGY, GBP and GRP, which vary sensitivity (LSB/volt) over
a 2:1 range. Incoming video signal amplitudes varying from
0.5 to 1.0 volt can be accommodated.
Input offset voltage of each converter is programmable in 1
LSB steps through the 6-bit OSGY, OSBP and OSRP regis-
ters. Range of adjustment is equivalent to –31 to +32 LSB.
A/D Converter
Each A/D converter digitizes the analog input into 8-bit data
words. Latency is 5–5
/
2
clock cycles, depending upon the
state of the INVSCK pin.
1
V
converters. V
bandgap voltage, V
REFIN
is the source of reference voltage for the three A/D
can be connected to either the internal
or an external voltage.
REFIN
REFOUT
Output Data Configuration
For RGB outputs, data format is unsigned binary: 00
corresponds to the lowest input; FF corresponds to the
highest input.
For YP
B
P
R
outputs, the data format is:
Y (0 to 700mV input): unsigned binary.
P
B
P
R
(±350mV input): twos-complement or offset binary.
Output data format is:
24-bit YP
16-bit YP
B
B
P
P
R
R
444
422
With 422 sampling, P
samples of Y, beginning with 0.
B
P
R
samples are coincident with even
HSOUT, L-to-H transition identifies the first sample.
Timing and Control
Timing and Control logic encompasses the Timing Generator,
PLL and Serial Interface.
Timing Generator
All internal clock and synchronization signals are generated
by the Timing Generator. Master Clock source is either the
PLL or the external clock input, XCK. Register bit, XCKSEL
selects the Master Clock source. Two clocks are generated.
Sampling clock, SCK is supplied to all three A/D converters.
Phase of SCK (relative to HSIN) can be adjusted in 32 11.25
degree phase increments using the 5-bit PHASE register.
Output data clocks, DCK and DCK are provided for
synchronizing data transfer from the digitizer outputs.
DCK and DCK are slaved to SCK.
Incoming horizontal sync HS
and Control to HS
edge with the output data.
IN
is propagated by the Timing
with a delay that aligns the leading
OUT
YG
IN
+350 mV
-350 mV
+700 mV
P
BIN
, P
RIN
ICLAMP
相關PDF資料
PDF描述
FMS9875KGC100X 1-Bit Bidirectional Voltage-Level Translator With Auto Direction Sensing and +/-15-kV ESD Protect 6-SOT -40 to 85
FMS9875KGC140 Integrated Photo Flash Charger and IGBT Driver 16-QFN -35 to 85
FMS9875KGC140X
FMS988AKAC100 Signal Conditioner
FMS988AKAC140 Signal Conditioner
相關代理商/技術參數
參數描述
FMS9875KGC100X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
FMS9875KGC140 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
FMS9875KGC140X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
FMS9875KWC 制造商:Fairchild Semiconductor Corporation 功能描述:
FMS9884A 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:3x8-Bit, 108/140/175 Ms/s Triple Video A/D Converter with Clamps
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*