- 您現在的位置：買賣IC網 > PDF目錄2068 > FAB2210UCX (Fairchild Semiconductor)IC SUBSYSTEM HDPH AMP G 20-WLCSP PDF資料下載
參數資料
| 型號： | FAB2210UCX |
| 廠商： | Fairchild Semiconductor |
| 文件頁數： | 12/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SUBSYSTEM HDPH AMP G 20-WLCSP |
| 標準包裝： | 1 |
| 類型： | D 類；G 類 |
| 輸出類型： | 1-通道（單聲道），帶立體聲耳機 |
| 在某負載時最大輸出功率 x 通道數量： | 3.3W x 1 @ 8 歐姆; 29mW x 2 @ 32 歐姆 |
| 電源電壓： | 2.8 V ~ 5.25 V |
| 特點： | 消除爆音，差分輸入，I²C，靜音，短路和熱保護，關機，音量控制 |
| 安裝類型： | 表面貼裝 |
| 供應商設備封裝： | 20-WLCSP |
| 封裝/外殼： | 20-UFBGA，WLCSP |
| 包裝： | 標準包裝 |
| 其它名稱： | FAB2210UCXFSDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
28
9614A–AT42–08/10
AT42QT2161
6.10
Address 11: Reset
Any nonzero value will trigger the device to reset. After a reset, the device will revert to default
settings.
After receiving a reset command the QT2161 will start not acknowledging I2C-compatible
communications and make CHANGE inactive within 16 ms. The chip will reset after another
~16 ms.
6.11
Address 12: LP Mode
LP mode sets the sleep time between bursts. A higher value causes more sleep time between
acquisitions resulting in lower power consumption, but slower response time.
The values are between 1 – 255, with each incrementing the sleep time by 16 ms steps. For
example, 1 = 16 ms LP, 2 = 32 ms LP, 3 = 48 ms LP, etc.
A value of zero causes the device to enter an ultra-low power mode (SLEEP), where no
measurements are carried out (see Section 3.17 on page 16).
The QT2161 is designed to sleep as much as possible to conserve power.
Note: the longer the LP mode, the longer the response time at first touch. The response time for
the first touch includes the digital filter's settling time (a few measurement cycles) and the DI
process. Above 256 ms LP mode the power consumption does not reduce as much, even with
longer LP mode durations. See Table 9-1 on page 46 for typical power consumptions.
Default value: 1 (16 ms LP)
6.12
Address 13: Burst Repetition
Burst Repetition (BREP) is a feature that enables the QT2161 to make multiple measurements
and take the average result; this improves the device’s ability to operate in noisy environments.
The number of burst repetitions can be reduced in low noise environments for faster response
time. The BREP value can range between 1 – 63 repetitions. Do not set to 0 because it is not
valid.
Default value:1 (one measurement burst)
Table 6-10.
Reset
Address
b7b6b5
b4b3b2b1
b0
11
RESET
Table 6-11.
LP Mode
Address
b7b6b5
b4b3b2b1
b0
12
LP_MODE
Table 6-12.
Burst Repetition
Address
b7b6b5
b4b3b2b1
b0
13
0
BREP
相關PDF資料 |
PDF描述 |
|---|---|
| FAB3103UCX | IC AMP AUD 2.3W CLASS D 12-WLCSP |
| FAN156L6X | IC COMPARATOR LV 6-MICROPAK |
| FAN256L8X | IC COMPARATOR DUAL LV 8-MICROPAK |
| FAN3800MLP24X | IC AMP AUDIO .016W STER AB 24MLP |
| FAN3850AUC19X | IC MICROPHONE PRE-AMP 6-WLCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAB24015AC | 制造商:Schneider Electric 功能描述:MOLDED CASE CIRCUIT BREAKER 480V 15A |
| FAB24020AC | 制造商:Schneider Electric 功能描述:MOLDED CASE CIRCUIT BREAKER 480V 20A |
| FAB24030AB | 制造商:Schneider Electric 功能描述:MOLDED CASE CIRCUIT BREAKER 480V 30A |
| FAB24030BC | 制造商:Schneider Electric 功能描述:MOLDED CASE CIRCUIT BREAKER 480V 30A |
| FAB24070AB | 制造商:Schneider Electric 功能描述:MOLDED CASE CIRCUIT BREAKER 480V 70A |
發布緊急采購，3分鐘左右您將得到回復。