- 您現在的位置：買賣IC網 > PDF目錄16539 > EVAL-ADV7180LQEBZ (Analog Devices Inc)BOARD EVALUATION ADV7180 PDF資料下載
參數資料
| 型號： | EVAL-ADV7180LQEBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 42/116頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION ADV7180 |
| 標準包裝： | 1 |
| 系列： | Advantiv® |
| 主要目的： | 視頻，SDTV 視頻解碼器 - NTSC，PAL，SECAM |
| 嵌入式： | 否 |
| 已用 IC / 零件： | ADV7180 |
| 主要屬性： | CVBS（復合），Y/C（S 視頻）和 YPrPb（元件）輸入 |
| 次要屬性： | 8 位 ITU-R BT.656 YCrCb 4:2:2 輸出 |
| 已供物品： | 板 |
| 相關產品： | ADV7180BCPZ-REEL-ND - IC VIDEO DECODER SDTV 40-LFCSP ADV7180BSTZ-ND - IC VIDEO DECODER SDTV 64-LQFP ADV7180BCPZ-ND - IC VIDEO DECODER SDTV 40-LFCSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
Data Sheet
ADV7180
Rev. I | Page 31 of 116
DEF_VAL_AUTO_EN, Default Value Automatic Enable,
Address 0x0C[1]
This bit enables the automatic use of the default values for Y, Cr,
and Cb when the ADV7180 cannot lock to the video signal.
Setting DEF_VAL_AUTO_EN to 0 disables free-run mode. If
the decoder is unlocked, it outputs noise.
Setting DEF_VAL_EN to 1 (default) enables free-run mode, and
a colored screen set by user-programmable Y, Cr, and Cb values
is displayed when the decoder loses lock.
CLAMP OPERATION
The input video is ac-coupled into the ADV7180. Therefore, its dc
value needs to be restored. This process is referred to as clamping
the video. This section explains the general process of clamping
on the ADV7180 and shows the different ways in which a user
can configure its behavior.
The ADV7180 uses a combination of current sources and a
digital processing block for clamping, as shown in Figure 22.
The analog processing channel shown is replicated three times
inside the IC. While only one single channel is needed for a
CVBS signal, two independent channels are needed for Y/C
(SVHS) type signals, and three independent channels are
needed to allow component signals (YPrPb) to be processed.
The clamping can be divided into two sections:
Clamping before the ADC (analog domain): current
sources.
Clamping after the ADC (digital domain): digital
processing block.
The ADC can digitize an input signal only if it resides within
the ADC 1.0 V input voltage range. An input signal with a dc
level that is too large or too small is clipped at the top or bottom
of the ADC range.
The primary task of the analog clamping circuits is to ensure that
the video signal stays within the valid ADC input window so that
the analog-to-digital conversion can take place. It is not necessary
to clamp the input signal with a very high accuracy in the analog
domain as long as the video signal fits within the ADC range.
After digitization, the digital fine clamp block corrects for any
remaining variations in dc level. Because the dc level of an input
video signal refers directly to the brightness of the picture
transmitted, it is important to perform a fine clamp with high
accuracy; otherwise, brightness variations may occur. Further-
more, dynamic changes in the dc level almost certainly lead to
visually objectionable artifacts and must, therefore, be prohibited.
The clamping scheme has to complete two tasks. It must acquire
a newly connected video signal with a completely unknown dc
level, and it must maintain the dc level during normal operation.
To acquire an unknown video signal quickly, the large current
clamps must be activated. It is assumed that the amplitude of
the video signal at this point is of a nominal value. Control of
the coarse and fine current clamp parameters is performed
automatically by the decoder.
Standard definition video signals may have excessive noise on
them. In particular, CVBS signals transmitted by terrestrial
broadcast and demodulated using a tuner usually show very
large levels of noise (>100 mV). A voltage clamp is unsuitable
for this type of video signal. Instead, the ADV7180 employs a
set of four current sources that can cause coarse (>0.5 mA) and
fine (<0.1 mA) currents to flow into and away from the high
impedance node that carries the video signal (see Figure 22).
The following sections describe the I2C signals that can be used
to influence the behavior of the clamping block.
CCLEN, Current Clamp Enable, Address 0x14[4]
The current clamp enable bit allows the user to switch off the
current sources in the analog front end altogether. This may be
useful if the incoming analog video signal is clamped externally.
When CCLEN is 0, the current sources are switched off.
When CCLEN is 1 (default), the current sources are enabled.
COARSE CURRENT SOURCES
FINE CURRENT SOURCES
DATA
PRE-
PROCESSOR
(DPP)
ADC
VIDEO PROCESSOR
WITH DIGITAL
FINE CLAMP
CLAMP CONTROL
ANALOG
VIDEO
INPUT
05700-
017
Figure 22. Clamping Overview
相關PDF資料 |
PDF描述 |
|---|---|
| REC5-2415DRWZ/H4/A | CONV DC/DC 5W 9-36VIN +/-15VOUT |
| VI-J4R-EZ-S | CONVERTER MOD DC/DC 7.5V 25W |
| VE-B1P-EW | CONVERTER MOD DC/DC 13.8V 100W |
| GBC20DRTF | CONN EDGECARD 40POS DIP .100 SLD |
| DK-2612-02 | CABLE FIBER OPTIC DUAL ST-SC 2M |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADV7181CLFEBZ | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Boxed Product (Development Kits) |
| EVAL-ADV7181CLQEBZ | 功能描述:BOARD EVAL FOR ADV7181CLQ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| EVAL-ADV7181DEBZ | 功能描述:EVAL BOARD FOR ADV7181D RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EVAL-ADV7181EBM | 制造商:Analog Devices 功能描述:UNRELEASED EVAL BOARD I.C. - Bulk |
| EVAL-ADV7182EBZ | 功能描述:視頻 IC 開發工具 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Evaluation Boards 類型:YPbPr to RGBHV Converters 工具用于評估:LMH1251 工作電源電壓:5 V |
發布緊急采購，3分鐘左右您將得到回復。