- 您現在的位置：買賣IC網 > PDF目錄362802 > EVAL-AD7853CB (Analog Devices, Inc.) 3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs PDF資料下載
參數資料
| 型號： | EVAL-AD7853CB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
| 中文描述： | 3 V至5 V單電源，200 kSPS的12位采樣ADC |
| 文件頁數： | 11/34頁 |
| 文件大?。?/td> | 350K |
| 代理商： | EVAL-AD7853CB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
REV. B
–11–
AD7853/AD7853L
STATUS REGISTER
The arrangement of the status register is shown below. The status register is a read-only register and contains 16 bits of data. The
status register is selected by first writing to the control register and putting two 1s in RDSLT1 and RDSLT0. The function of the
bits in the status register are described below. The power-up status of all bits is 0.
WRITE TO CONTROL REGISTER
SETTING RDSLT0 = RDSLT1 = 1
START
READ STATUS REGISTER
Figure 6. Flowchart for Reading the Status Register
MSB
ZERO
BUSY
ZERO
ZERO
ZERO
ZERO
PMGT1
PMGT0
RDSLT1
RDSLT0
2/
3
MODE
X
CALMD
CALSLT1
CALSLT0
STCAL
LSB
Status Register Bit Function Descriptions
Bit
Mnemonic
Comment
15
14
ZERO
BUSY
This bit is always 0.
Conversion/Calibration Busy Bit. When this bit is 1, it indicates that there is a conversion or calibration in
progress. When this bit is 0, no conversion or calibration is in progress.
These four bits are always 0.
13
12
11
10
9
8
7
6
5
ZERO
ZERO
ZERO
ZERO
PMGT1
PMGT0
RDSLT1
RDSLT0
2/
3
MODE
Power Management Bits. These bits, along with the
SLEEP
pin, will indicate whether or not the part is in a
power-down mode. See Table VI in Power-Down Section for description.
Both of these bits are always 1, indicating it is the status register that is being read. See Table II.
Interface Mode Select Bit. With this bit at 0, the device is in Interface Mode 2. With this bit at 1, the device
is in Interface Mode 1. This bit is reset to 0 after every read cycle.
Don’t care bit.
Calibration Mode Bit. A 0 in this bit indicates a self-calibration is selected; a 1 in this bit indicates a system
calibration is selected (see Table III).
Calibration Selection Bits and Start Calibration Bit. The STCAL bit is read as a 1 if a calibration is in
progress and as a 0 if no calibration is in progress. The CALSLT1 and CALSLT0 bits indicate
which of the calibration registers are addressed for reading and writing (see section on the Calibration
Registers for more details).
4
3
X
CALMD
2
1
0
CALSLT1
CALSLT0
STCAL
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7854CB | 3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs |
| EVAL-AD7856CB | 5 V Single Supply, 8-Channel 14-Bit 285 kSPS Sampling ADC |
| EVAL-AD7858CB | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| EVAL-AD7859CB | 3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADCs |
| EVAL-AD7866CB | Dual 1 MSPS, 12-Bit, 2-Channel SAR ADC with Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7854CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD - Bulk |
| EVAL-AD7856CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:5 V Single Supply, 8-Channel 14-Bit 285 kSPS Sampling ADC |
| EVAL-AD7858CB | 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD - Bulk |
| EVAL-AD7858CB4 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V to 5 V Single Supply, 200 kSPS 8-Channel, 12-Bit Sampling ADC |
| EVAL-AD7859CB | 制造商:Analog Devices 功能描述:Evaluation Board For 3V To 5V, 12-Bit 200KSPS, Multi-Channel, Sampling ADC |
發布緊急采購，3分鐘左右您將得到回復。