- 您現在的位置：買賣IC網 > PDF目錄362802 > EVAL-AD7730LEB (Analog Devices, Inc.) 10K RESISTOR 1/10 W PDF資料下載
參數資料
| 型號： | EVAL-AD7730LEB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | 10K RESISTOR 1/10 W |
| 中文描述： | 橋傳感器模數轉換器 |
| 文件頁數： | 18/52頁 |
| 文件大?。?/td> | 497K |
| 代理商： | EVAL-AD7730LEB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
AD7730/AD7730L
–18–
REV. A
Bit
Location
MR2
Bit
Mnemonic
BO
Description
Burnout Current Bit. A 1 in this bit activates the burnout currents. When active, the burnout currents
connect to the selected analog input pair, one source current to the AIN(+) input and one sink current to
the AIN(–) input. A 0 in this bit turns off the on-chip burnout currents.
MR1–MR0
CH1–CH0
Channel Selection Bits. T hese bits select the analog input channel to be converted or calibrated as
outlined in T able X III. With CH1 at 1 and CH0 at 0, the part looks at the AIN1(–) input internally
shorted to itself. T his can be used as a test method to evaluate the noise performance of the part with
no external noise sources. In this mode, the AIN1(–) input should be connected to an external voltage
within the allowable common-mode range of the part. T he Offset and Gain Calibration Registers on
the part are paired. T here are three pairs of calibration registers labelled Register Pair 0 through Regis-
ter Pair 2. T hese are assigned to the input channel pairs as outlined in T able X III.
T able X III. Channel Selection
Input Channel Pair
Positive Input
AIN1(+)
AIN2(+)
AIN1(–)
AIN1(–)
CH1
0
0
1
1
CH0
0
1
0
1
Negative Input
AIN1(–)
AIN2(–)
AIN1(–)
AIN2(–)
Calibration Register Pair
Register Pair 0
Register Pair 1
Register Pair 0
Register Pair 2
Filter Register (RS2-RS0 = 0, 1, 1); Power-On/Reset Status: 200010 Hex
T he Filter Register is a 24-bit register from which data can be read or to which data can be written. T his register determines the
amount of averaging performed by the filter and the mode of operation of the filter. It also sets the chopping mode and the delay
associated with chopping the inputs. T able X IV outlines the bit designations for the Filter Register. FR0 through FR23 indicate the
bit location, FR denoting the bits are in the Filter Register. FR23 denotes the first bit of the data stream. T he number in brackets
indicates the power-on/reset default status of that bit. Figure 5 shows a flowchart for reading from the registers on the AD7730 and
Figure 6 shows a flowchart for writing to the registers on the part.
T able X IV. Filter Register
FR23
FR22
FR21
FR20
FR19
FR18
FR17
FR16
SF11 (0)
SF10 (0)
SF9 (1)
SF8 (0)
SF7 (0)
SF6 (0)
SF5 (0)
SF4 (0)
FR15
FR14
FR13
FR12
FR11
FR10
FR9
FR8
SF3 (0)
SF2 (0)
SF1 (0)
SF0 (0)
ZERO (0)
ZERO (0)
SK IP (0)
FAST (0)
FR7
FR6
FR5
FR4
FR3
FR2
FR1
FR0
ZERO (0)
ZERO (0)
AC (0)
CHP (1)
DL3 (0)
DL2 (0)
DL1 (0)
DL0 (0)
Bit
Location
FR23–FR12
Bit
Mnemonic
SF11–SF0
Description
Sinc
3
Filter Selection Bits. T he AD7730 contains two filters: a sinc
3
filter and an FIR filter. T he 12 bits
programmed to SF11 through SF0 set the amount of averaging the sinc
3
filter performs. As a result,
the number programmed to these 12 bits affects the –3 dB frequency and output update rate from the
part (see Filter Architecture section). T he allowable range for SF words depends on whether the part
is operated with CHOP on or off and SK IP on or off. T able X V outlines the SF ranges for different
setups. All output update rates will be one-half those quoted in T able X V for the AD7730L operating
with a 2.4576 MHz clock.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7730EB | Bridge Transducer ADC |
| EVAL-AD7731EB | Low Noise, High Throughput 24-Bit Sigma-Delta ADC |
| EVAL-AD7751EB | Energy Metering IC With On-Chip Fault Detection |
| EVAL-AD7755EB | Energy Metering IC with Pulse Output |
| EVAL-AD7783EB | Read-Only, Pin Configured 24-Bit ADC with Excitation Current Sources |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7730LEBZ | 功能描述:BOARD EVALUATION FOR AD7730 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7731EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7731EBZ | 功能描述:BOARD EVALUATION FOR AD7731 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7732EB | 制造商:Analog Devices 功能描述:2-CHANNEL, ??10 V INPUT RANGE, HIGH THROUGHPUT, 24-BIT ADC |
| EVAL-AD7732EBZ | 功能描述:BOARD EVAL FOR AD7732 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。