參數資料
型號： EVAL-AD7730LEB
廠商： Analog Devices, Inc.
英文描述： 10K RESISTOR 1/10 W
中文描述： 橋傳感器模數轉換器
文件頁數： 15/52頁
文件大小： 497K
代理商： EVAL-AD7730LEB
AD7730/AD7730L
REV. A
–15–
Data Register (RS2–RS0 = 0, 0, 1); Power On/Reset Status: 000000 Hex
T he Data Register on the part is a read-only register which contains the most up-to-date conversion result from the AD7730. Fig-
ure5 shows a flowchart for reading from the registers on the AD7730. T he register can be programmed to be either 16 bits or 24bits
wide, determined by the status of the WL bit of the Mode Register. T he
RDY
output and
RDY
bit of the Status Register are set low
when the Data Register is updated. T he
RDY
pin and
RDY
bit will return high once the full contents of the register (either 16 bits or
24 bits) have been read. If the Data Register has not been read by the time the next output update occurs, the
RDY
pin and
RDY
bit
will go high for at least 100
×
t
CLK IN
, indicating when a read from the Data Register should not be initiated to avoid a transfer from
the Data Register as it is being updated. Once the updating of the Data Register has taken place,
RDY
returns low.
If the Communications Register data sets up the part for a write operation to this register, a write operation must actually take place
in order to return the part to where it is expecting a write operation to the Communications Register (the default state of the inter-
face). However, the 16 or 24 bits of data written to the part will be ignored by the AD7730.
Mode Register (RS2–RS0 = 0, 1, 0); Power On/Reset Status: 01B0 Hex
T he Mode Register is a 16-bit register from which data can be read or to which data can be written. T his register configures
the operating modes of the AD7730, the input range selection, the channel selection and the word length of the Data Register.
T able X outlines the bit designations for the Mode Register. MR0 through MR15 indicate the bit location, MR denoting the bits are
in the Mode Register. MR15 denotes the first bit of the data stream. T he number in brackets indicates the power-on/reset default
status of that bit. Figure 5 shows a flowchart for reading from the registers on the AD7730 and Figure 6 shows a flowchart for writ-
ing to the registers on the part.
T able X . Mode Register
MR15
MR14
MR13
MR12
MR11
MR10
MR9
MR8
MD2 (0)
MD1 (0)
MD0 (0)
B
/U (0)
DEN (0)
D1 (0)
D0 (0)
WL (1)
MR7
MR6
MR5
MR4
MR3
MR2
MR1
MR0
HIREF (1)
ZERO (0)
RN1 (1)
RN0 (1)
CLK DIS (0)
BO (0)
CH1 (0)
CH0 (0)
Bit
Location
Bit
Mnemonic
Description
MR15–MR13
MD2–MD0
Mode Bits. T hese three bits determine the mode of operation of the AD7730 as outlined in
T able X I. T he modes are independent, such that writing new mode bits to the Mode Register
will exit the part from the mode in which it is operating and place it in the new requested mode
immediately after the Mode Register write. T he function of the mode bits is described in more
detail below.
T able X I. Operating Modes
MD2
MD1
MD0
Mode of Operation
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Sync (Idle) Mode
Continuous Conversion Mode
Single Conversion Mode
Power-Down (Standby) Mode
Internal Zero-Scale Calibration
Internal Full-Scale Calibration
System Zero-Scale Calibration
System Full-Scale Calibration
Power-On/Reset Default
相關PDF資料
PDF描述
EVAL-AD7730EB Bridge Transducer ADC
EVAL-AD7731EB Low Noise, High Throughput 24-Bit Sigma-Delta ADC
EVAL-AD7751EB Energy Metering IC With On-Chip Fault Detection
EVAL-AD7755EB Energy Metering IC with Pulse Output
EVAL-AD7783EB Read-Only, Pin Configured 24-Bit ADC with Excitation Current Sources
相關代理商/技術參數
參數描述
EVAL-AD7730LEBZ 功能描述:BOARD EVALUATION FOR AD7730 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7731EB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-AD7731EBZ 功能描述:BOARD EVALUATION FOR AD7731 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7732EB 制造商:Analog Devices 功能描述:2-CHANNEL, ??10 V INPUT RANGE, HIGH THROUGHPUT, 24-BIT ADC
EVAL-AD7732EBZ 功能描述:BOARD EVAL FOR AD7732 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*