參數資料
型號: EVAL-AD7328SDZ
廠商: Analog Devices Inc
文件頁數: 20/37頁
文件大?。?/td> 0K
描述: BOARD EVAL FOR AD7328
標準包裝: 1
系列: iCMOS®
ADC 的數量: 1
位數: 12
采樣率(每秒): 1M
數據接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
輸入范圍: ±10 V
在以下條件下的電源(標準): 31mW @ 1MSPS
工作溫度: -40°C ~ 85°C
已用 IC / 零件: AD7328
已供物品:
AD7328
Data Sheet
Rev. C | Page 26 of 36
If a write to one of the range registers is required during a se-
quence, it is necessary to first stop the sequence by writing to
the control register and setting SEQ1 to 0 and SEQ2 to 0. Next,
write to the range register to change the required range. The
previously selected sequence should then be initiated again by
writing to the control register and setting SEQ1 to 0 and SEQ2
to 1. The ADC converts the first channel in the sequence.
The AD7328 can be configured to convert a sequence of con-
secutive channels (see Figure 45). This sequence begins by
converting on Channel 0 and ends with a final channel as selected
by Bit ADD2 to Bit ADD0 in the control register. In this config-
uration, there is no need for a write to the sequence register. To
operate the AD7328 in this mode, set SEQ1 to 1 and SEQ2 to 0
in the control register, and then select the final channel in the
sequence by programming Bit ADD2 to Bit ADD0 in the control
register.
After the control register is configured to operate the AD7328
in this mode, the DIN line can be held low or the write bit can
be set to 0. To return to traditional multichannel operation, a
write to the control register to set SEQ1 to 0 and SEQ2 to 0 is
necessary.
When SEQ1 and SEQ2 are both set to 0 or to 1, the AD7328 is
configured to operate in traditional multichannel mode, where
a write to Channel Address Bit ADD2 to Bit ADD0 in the
control register selects the next channel for conversion.
DIN: WRITE TO RANGE REGISTER 1 TO SELECT THE RANGE
FOR ANALOG INPUT CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 0, ± 10V
RANGE, SINGLE-ENDED MODE.
CS
DIN: WRITE BIT = 0 OR DIN LINE HELD LOW TO CONTINUE
THROUGH SEQUENCE OF CONSECUTIVE CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 1,
RANGE SELECTED IN RANGE REGISTER 1.
CS
DIN: WRITE TO RANGE REGISTER 2 TO SELECT THE RANGE
FOR ANALOG INPUT CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
RANGE SELECTED IN RANGE REGISTER 1,
SINGLE-ENDED MODE.
CS
DIN: WRITE BIT = 0 OR DIN LINE HELD LOW TO CONTINUE
TO CONVERT THROUGH THE SEQUENCE OF
CONSECUTIVE CHANNELS.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
RANGE SELECTED IN RANGE REGISTER 1.
CS
DIN: WRITE TO CONTROL REGISTER TO SELECT THE FINAL
CHANNEL IN THE CONSECUTIVE SEQUENCE, SET SEQ1 = 1
AND SEQ2 = 0. SELECT OUTPUT CODING FOR SEQUENCE.
DOUT: CONVERSION RESULT FROM CHANNEL 0,
RANGE SELECTED IN RANGE REGISTER 1,
SINGLE-ENDED MODE.
CS
POWER ON.
DIN TIED LOW/WRITE BIT = 0.
04852-
032
CONTINUOUSLY CONVERT
ON CONSECUTIVE SEQUENCE
OF CHANNELS.
DIN: WRITE TO CONTROL
REGISTER TO STOP THE
SEQUENCE, SEQ1 = 0, SEQ2 = 0.
DOUT: CONVERSION RESULT
FROM CHANNEL IN SEQUENCE.
CS
STOPPING
A SEQUENCE.
Figure 45. Flowchart for Consecutive Sequence of Channels
相關PDF資料
PDF描述
ESC06DRTH-S734 CONN EDGECARD 12POS DIP .100 SLD
ECC31DCAI CONN EDGECARD 62POS R/A .100 SLD
EVAL-AD7276SDZ BOARD EVAL FOR AD7276
ABC05DRYS CONN EDGECARD 10POS .100 DIP SLD
ESC06DREI-S734 CONN EDGECARD 12POS .100 EYELET
相關代理商/技術參數
參數描述
EVAL-AD7329CB 制造商:Analog Devices 功能描述:
EVAL-AD7329CBZ 功能描述:BOARD EVALUATION FOR AD7329CBZ RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD73311EB 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End
EVAL-AD73311EZ 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End
EVAL-AD73311LEB 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End