- 您現在的位置：買賣IC網 > PDF目錄17048 > EVAL-AD7328SDZ (Analog Devices Inc)BOARD EVAL FOR AD7328 PDF資料下載
參數資料
| 型號： | EVAL-AD7328SDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 24/37頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7328 |
| 標準包裝： | 1 |
| 系列： | iCMOS® |
| ADC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 1M |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 輸入范圍： | ±10 V |
| 在以下條件下的電源（標準）： | 31mW @ 1MSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7328 |
| 已供物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Data Sheet
AD7328
Rev. C | Page 29 of 36
AUTOSHUTDOWN MODE
(PM1 = 1, PM0 = 0)
Once the autoshutdown mode is selected, the AD7328 auto-
matically enters shutdown on the 15th SCLK rising edge. In
autoshutdown mode, all internal circuitry is powered down.
The AD7328 retains information in the registers during
autoshutdown. The track-and-hold is in hold mode during
autoshutdown. On the rising CS edge, the track-and-hold,
which was in hold during shutdown, returns to track as the
AD7328 begins to power up. The time to power-up from auto-
shutdown is 500 s.
When the control register is programmed to transition to
autoshutdown mode, it does so on the 15th SCLK rising edge.
Figure 50 shows the part entering the autoshutdown mode.
When the AD7328 is in autoshutdown mode, the CS signal
must remain low to keep the part in autoshutdown mode. The
AD7328 automatically begins to power up on the CS rising edge.
The tPOWER-UP is required before a valid conversion, initiated by
bringing the CS signal low, can take place. After this valid con-
version is complete, the AD7328 powers down again on the 15th
SCLK rising edge. The CS signal must remain low to keep the
part in autoshutdown mode.
AUTOSTANDBY MODE
(PM1 = 0, PM0 = 1)
In autostandby mode, portions of the AD7328 are powered
down, but the on-chip reference remains powered up. The
reference bit in the control register should be 1 to ensure that
the on-chip reference is enabled. This mode is similar to auto-
shutdown but allows the AD7328 to power up much faster,
which allows faster throughput rates.
As is the case with autoshutdown mode, the AD7328 enters
standby on the 15th SCLK rising edge when the control register
is updated (see Figure 50). The part retains information in the
registers during standby. The AD7328 remains in standby until
it receives a CS rising edge. The ADC begins to power up on the
CS rising edge. On the CS rising edge, the track-and-hold,
which was in hold mode while the part was in standby, returns
to track.
The power-up time from standby is 700 ns. The user should
ensure that 700 ns have elapsed before bringing CS low to
attempt a valid conversion. After this valid conversion is
complete, the AD7328 again returns to standby on the 15th
SCLK rising edge. The CS signal must remain low to keep the
part in standby mode.
Figure 50 shows the part entering autoshutdown mode. The
sequence of events is the same when entering autostandby mode.
In Figure 50, the power management bits are configured for auto-
shutdown. For autostandby mode, the power management bits,
PM1 and PM0, should be set to 0 and 1, respectively.
04852-
042
CS
1
16
15
1
16
15
SCLK
SDATA
DIN
VALID DATA
DATA INTO CONTROL REGISTER
tPOWER-UP
CONTROL REGISTER IS LOADED ON THE FIRST 15 CLOCKS,
PM1 = 1, PM0 = 0
PART ENTERS SHUTDOWN MODE
ON THE 15TH RISING SCLK EDGE
AS PM1 = 1, PM0 = 0
PART BEGINS TO POWER
UP ON CS RISING EDGE
THE PART IS FULLY POWERED UP
ONCE
tPOWER-UP HAS ELAPSED
Figure 50. Entering Autoshutdown/Autostandby Mode
相關PDF資料 |
PDF描述 |
|---|---|
| ESC06DRTH-S734 | CONN EDGECARD 12POS DIP .100 SLD |
| ECC31DCAI | CONN EDGECARD 62POS R/A .100 SLD |
| EVAL-AD7276SDZ | BOARD EVAL FOR AD7276 |
| ABC05DRYS | CONN EDGECARD 10POS .100 DIP SLD |
| ESC06DREI-S734 | CONN EDGECARD 12POS .100 EYELET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7329CB | 制造商:Analog Devices 功能描述: |
| EVAL-AD7329CBZ | 功能描述:BOARD EVALUATION FOR AD7329CBZ RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD73311EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End |
| EVAL-AD73311EZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End |
| EVAL-AD73311LEB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Low Cost, Low Power CMOS General Purpose Analog Front End |
發布緊急采購，3分鐘左右您將得到回復。