- 您現在的位置：買賣IC網 > PDF目錄17048 > EVAL-AD7194EBZ (Analog Devices Inc)EVAL BOARD FOR AD7194 PDF資料下載
參數資料
| 型號： | EVAL-AD7194EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 41/57頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR AD7194 |
| 設計資源： | EVAL-AD7zzzEBZ Schematic AD7194 Gerber Files |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 數據接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7194 |
| 已供物品： | 板，線纜 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁
Data Sheet
AD7194
Rev. A | Page 45 of 56
CHOP ENABLED (SINC3 FILTER)
With chop enabled, the ADC offset and offset drift are
minimized. The analog input pins are continuously swapped.
With the analog input pins connected in one direction, the
settling time of the sinc filter is allowed and a conversion is
recorded. The analog input pins invert and another settled
conversion is obtained. Subsequent conversions are averaged
to minimize the offset. This continuous swapping of the analog
input pins and the averaging of subsequent conversions means
that the offset drift is also minimized. With chop enabled, the
resolution increases by 0.5 bits. Using the sinc3 filter with chop
enabled is suitable for output data rates up to 320 Hz.
SINC3/SINC4
POST FILTER
MODULATOR
ADC
CHOP
08566-
047
Figure 48. Chop Enabled (Sinc3 Chop Enabled)
Output Data Rate and Settling Time (Sinc3 Chop
Enabled)
For the sinc3 filter, the output data rate is equal to
fADC = fCLK/(3 × 1024 × FS[9:0])
where:
fADC is the output data rate.
fCLK is the master clock (4.92 MHz nominal).
FS[9:0] is the decimal equivalent of Bit FS9 to Bit FS0 in the
mode register.
The value of FS[9:0] can be varied from 1 to 1023. This results
in an output data rate of 1.56 Hz to 1600 Hz. The settling time
is equal to
tSETTLE = 2/fADC
Table 33. Examples of Output Data Rates and the
Corresponding Settling Time (Chop Enabled, Sinc3 Filter)
FS[9:0]
Output Data Rate (Hz)
Settling Time (ms)
96
16.7
120
80
20
100
When a channel change occurs, the modulator and filter are
reset. The complete settling time is required to generate the first
conversion after the channel change. Subsequent conversions on
this channel occur at 1/fADC.
CHANNEL
CONVERSIONS
CHANNEL A
CH A
CH B
CHANNEL B
1/
fADC
CH B
08566-
048
Figure 49. Channel Change (Sinc3 Chop Enable)
If conversions are performed on a single channel and a step
change occurs, the ADC does not detect the change in analog
input; therefore, it continues to output conversions at the
programmed output data rate. However, it is at least two
conversions later before the output data accurately reflects
the analog input. If the step change occurs while the ADC is
processing a conversion, then the ADC takes three conversions
after the step change to generate a fully settled result.
1/
fADC
ANALOG
INPUT
ADC
OUTPUT
FULLY
SETTLED
08566-
049
Figure 50. Asynchronous Step Change in Analog Input (Sinc3 Chop Enabled)
The cutoff frequency f3dB is equal to
f3dB = 0.24 × fADC
50 Hz/60 Hz Rejection (Sinc3 Chop Enabled)
When FS[9:0] is set to 96 and chopping is enabled, the filter
response shown in Figure 51 is obtained. The output data rate
is equal to 16.7 Hz for a 4.92 MHz master clock. The chopping
introduces notches at odd integer multiples of fADC/2. The
notches due to the sinc filter is addition to the notches intro-
duced by the chopping means that simultaneous 50 Hz and
60 Hz rejection is achieved for an output data rate of 16.7 Hz.
The rejection at 50 Hz/60 Hz ± 1 Hz is typically 53 dB,
assuming a stable master clock.
–120
–110
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
25
50
75
100
125
150
FREQUENCY (Hz)
FILTE
R
GA
IN
(
dB
)
08566-
050
Figure 51. Sinc3 Filter Response (FS[9:0] = 96, Chop Enabled)
相關PDF資料 |
PDF描述 |
|---|---|
| ECC22DCMT-S288 | CONN EDGECARD 44POS .100 EXTEND |
| 0210490257 | CABLE JUMPER 1.25MM .051M 20POS |
| ADR445ARMZ-REEL7 | IC VREF SERIES PREC 5V 8-MSOP |
| RBC19DRYN-S13 | CONN EDGECARD 38POS .100 EXTEND |
| HKQ0603S0N7C-T | INDUCTOR HI FREQ 0.7NH 0201 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7195EBZ | 功能描述:BOARD EVAL FOR AD7195 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7262EDZ | 功能描述:BOARD EVAL CONTROL AD7262 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7264EDZ | 功能描述:BOARD EVALUATION FOR AD7264 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7265CB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential/Single-Ended Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC |
| EVAL-AD7265CB1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Differential Input, Dual 1 MSPS, 12-Bit, 3-Channel SAR ADC |
發布緊急采購，3分鐘左右您將得到回復。