- 您現在的位置：買賣IC網 > PDF目錄17115 > EA-QSB-012 (Embedded Artists)BOARD QUICK START LPC1343 PDF資料下載
參數資料
| 型號： | EA-QSB-012 |
| 廠商： | Embedded Artists |
| 文件頁數： | 8/74頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD QUICK START LPC1343 |
| 標準包裝： | 1 |
| 系列： | LPC13xx |
| 類型： | MCU |
| 適用于相關產品： | LPC1343 |
| 所含物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
LPC1311_13_42_43
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 5 — 6 June 2012
16 of 74
NXP Semiconductors
LPC1311/13/42/43
32-bit ARM Cortex-M3 microcontroller
[1]
Pin state at reset for default function: I = Input; O = Output; PU = internal pull-up enabled (for VDD = 3.3 V, pin is pulled up to 2.6 V for
parts LPC1311/13/42/43 and pulled up to 3.3 V for parts LPC1311/01 and LPC1313/01); IA = inactive, no pull-up/down enabled.
F = floating; floating pins, if not used, should be tied to ground or power to minimize power consumption.
[2]
5 V tolerant pad. See Figure 37 for pad characteristics. RESET functionality is not available in Deep power-down mode. Use the
WAKEUP pin to reset the chip and wake up from Deep power-down mode. An external pull-up resistor is required on this pin for the
Deep power-down mode.
[3]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors and configurable hysteresis (see Figure 36).
[4]
I2C-bus pads compliant with the I2C-bus specification for I2C standard mode and I2C Fast-mode Plus.
[5]
5 V tolerant pad providing digital I/O functions with configurable pull-up/pull-down resistors, configurable hysteresis, and analog input.
When configured as a ADC input, digital section of the pad is disabled, and the pin is not 5 V tolerant (see Figure 36).
[6]
Pad provides USB functions. It is designed in accordance with the USB specification, revision 2.0 (Full-speed and Low-speed mode
only). This pad is not 5 V tolerant.
[7]
When the system oscillator is not used, connect XTALIN and XTALOUT as follows: XTALIN can be left floating or can be grounded
(grounding is preferred to reduce susceptibility to noise). XTALOUT should be left floating.
PIO1_7/TXD/
CT32B0_MAT1
32[3] yes
I/O
I; PU
PIO1_7 — General purpose digital input/output pin.
O-
TXD — Transmitter output for UART.
O-
CT32B0_MAT1 — Match output 1 for 32-bit timer 0.
PIO1_8/
CT16B1_CAP0
yes
I/O
I; PU
PIO1_8 — General purpose digital input/output pin.
I-
CT16B1_CAP0 — Capture input 0 for 16-bit timer 1.
PIO1_9/
CT16B1_MAT0
12[3] yes
I/O
I; PU
PIO1_9 — General purpose digital input/output pin.
O-
CT16B1_MAT0 — Match output 0 for 16-bit timer 1.
PIO1_10/AD6/
CT16B1_MAT1
20[5] yes
I/O
I; PU
PIO1_10 — General purpose digital input/output pin.
I-
AD6 — A/D converter, input 6.
O-
CT16B1_MAT1 — Match output 1 for 16-bit timer 1.
PIO1_11/AD7
27[5] yes
I/O
I; PU
PIO1_11 — General purpose digital input/output pin.
I-
AD7 — A/D converter, input 7.
PIO2_0/DTR
yes
I/O
I; PU
PIO2_0 — General purpose digital input/output pin.
O-
DTR — Data Terminal Ready output for UART.
PIO3_2
28[3] yes
I/O
I; PU
PIO3_2 — General purpose digital input/output pin.
PIO3_4
13[3] no
I/O
I; PU
PIO3_4 — General purpose digital input/output pin (LPC1311/13 only).
PIO3_5
14[3] no
I/O
I; PU
PIO3_5 — General purpose digital input/output pin (LPC1311/13 only).
USB_DM
13[6] no
I/O
F
USB_DM — USB bidirectional D
line (LPC1342/43 only).
USB_DP
14[6] no
I/O
F
USB_DP — USB bidirectional D+ line (LPC1342/43 only).
VDD
6;
29
-
I
-
3.3 V supply voltage to the internal regulator, the external rail, and the
ADC. Also used as the ADC reference voltage.
XTALIN
-
I
-
Input to the oscillator circuit and internal clock generator circuits. Input
voltage must not exceed 1.8 V.
XTALOUT
-
O
-
Output from the oscillator amplifier.
VSS
33
-
Thermal pad. Connect to ground.
Table 4.
LPC1311/13/42/43 HVQFN33 pin description table …continued
Symbol
Pin
Start
logic
input
Type Reset
state
[1]
Description
相關PDF資料 |
PDF描述 |
|---|---|
| EEM25DRYN-S13 | CONN EDGECARD 50POS .156 EXTEND |
| MAX8808XETA+TG104 | IC CHARGER LI+ SGLL CCCV 8TDFN |
| EEC18DREI-S734 | CONN EDGECARD 36POS .100 EYELET |
| EEC25DRES-S93 | CONN EDGECARD 50POS .100 EYELET |
| VE-JTF-EZ | CONVERTER MOD DC/DC 72V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EA-QSB-015 | 功能描述:開發板和工具包 - ARM QUICK START BOARD LPC11U35 RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EA-QSB-016 | 制造商:Embedded Artists 功能描述:BOARD QUICK START LPC4088 |
| EA-QSB-017 | 制造商:Embedded Artists 功能描述:BOARD QSB BASE LPC4088 |
| EA-QSB-100 | 功能描述:開發板和工具包 - ARM QUICKSTART PROTOTYPE BRD RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EA-QSB-102 | 功能描述:開發板和工具包 - ARM QUICKSTART PROTOTYPE BRD W/ LPC2106 RS232 RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。