- 您現在的位置：買賣IC網 > PDF目錄17115 > EA-QSB-012 (Embedded Artists)BOARD QUICK START LPC1343 PDF資料下載
參數資料
| 型號： | EA-QSB-012 |
| 廠商： | Embedded Artists |
| 文件頁數： | 29/74頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD QUICK START LPC1343 |
| 標準包裝： | 1 |
| 系列： | LPC13xx |
| 類型： | MCU |
| 適用于相關產品： | LPC1343 |
| 所含物品： | 板 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁
LPC1311_13_42_43
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2012. All rights reserved.
Product data sheet
Rev. 5 — 6 June 2012
35 of 74
NXP Semiconductors
LPC1311/13/42/43
32-bit ARM Cortex-M3 microcontroller
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (25
°C), nominal supply voltages.
[2]
For LPC1342 and LPC1343 only: For USB operation 3.0 V
≤ VDD ≤ 3.6 V. Guaranteed by design.
[3]
IRC enabled; system oscillator disabled; system PLL disabled.
[4]
IDD measurements were performed with all pins configured as GPIO outputs driven LOW and pull-up resistors disabled.
[5]
BOD disabled.
[6]
All peripherals disabled in the SYSAHBCLKCTRL register. Peripheral clocks to UART, SSP, trace clock, and SysTick timer disabled in
the syscon block.
[7]
For LPC1342/43: USB_DP and USB_DM pulled LOW externally.
[8]
IRC disabled; system oscillator enabled; system PLL enabled.
[9]
All oscillators and analog blocks turned off in the PDSLEEPCFG register; PDSLEEPCFG = 0x0000 0FFF.
[10] WAKEUP pin pulled HIGH externally. An external pull-up resistor is required on the RESET pin for the Deep power-down mode.
[11] Low-current mode PWR_LOW_CURRENT selected when running the set_power routine in the power profiles.
[12] Including voltage on outputs in 3-state mode.
[13] VDD supply voltage must be present.
[14] 3-state outputs go into 3-state mode in Deep power-down mode.
[15] Allowed as long as the current limit does not exceed the maximum current allowed by the device.
[16] To VSS.
[17] 3.0 V
≤ VDD ≤ 3.6 V.
[18] Includes external resistors of 33
Ω± 1 % on USB_DP and USB_DM.
[1]
The ADC is monotonic, there are no missing codes.
[2]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 8.
VOH
HIGH-level output
voltage
driven; for low-/full-speed;
RL of 15 k
Ω to GND
[17] 2.8
-
3.5
V
Ctrans
transceiver capacitance pin to GND
[17] --20
pF
ZDRV
driver output
impedance for driver
which is not high-speed
capable
with 33
Ω series resistor; steady state
drive
[18][17] 36
-
44.1
Ω
Table 7.
Static characteristics …continued
Tamb =
40 °C to +85 °C, unless otherwise specified.
Symbol Parameter
Conditions
Min
Typ[1]
Max
Unit
Table 8.
ADC static characteristics
Tamb =
40 °C to +85 °C unless otherwise specified; ADC frequency 4.5 MHz, VDD = 2.5 V to 3.6 V.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
VIA
analog input voltage
0
-
VDD
V
Cia
analog input capacitance
-
1
pF
ED
differential linearity error
[1][2] --
±1LSB
EL(adj)
integral non-linearity
[3] --
±1.5
LSB
EO
offset error
[4] --
±3.5
LSB
EG
gain error
[5] --0.6
%
ET
absolute error
[6] --
±4LSB
Rvsi
voltage source interface
resistance
--40
k
Ω
Ri
input resistance
[7][8] --2.5
M
Ω
相關PDF資料 |
PDF描述 |
|---|---|
| EEM25DRYN-S13 | CONN EDGECARD 50POS .156 EXTEND |
| MAX8808XETA+TG104 | IC CHARGER LI+ SGLL CCCV 8TDFN |
| EEC18DREI-S734 | CONN EDGECARD 36POS .100 EYELET |
| EEC25DRES-S93 | CONN EDGECARD 50POS .100 EYELET |
| VE-JTF-EZ | CONVERTER MOD DC/DC 72V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EA-QSB-015 | 功能描述:開發板和工具包 - ARM QUICK START BOARD LPC11U35 RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EA-QSB-016 | 制造商:Embedded Artists 功能描述:BOARD QUICK START LPC4088 |
| EA-QSB-017 | 制造商:Embedded Artists 功能描述:BOARD QSB BASE LPC4088 |
| EA-QSB-100 | 功能描述:開發板和工具包 - ARM QUICKSTART PROTOTYPE BRD RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EA-QSB-102 | 功能描述:開發板和工具包 - ARM QUICKSTART PROTOTYPE BRD W/ LPC2106 RS232 RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
發布緊急采購，3分鐘左右您將得到回復。