參數資料
型號： DSPIC30F6010-20E/PF
廠商： Microchip Technology
文件頁數： 87/110頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 144K 80TQFP
產品培訓模塊： Asynchronous Stimulus
標準包裝： 90
系列： dsPIC™ 30F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 20 MIPS
連通性： CAN，I²C，SPI，UART/USART
外圍設備： 高級欠壓探測/復位，LVD，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 68
程序存儲器容量： 144KB（48K x 24）
程序存儲器類型： 閃存
EEPROM 大?。?/td> 4K x 8
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
數據轉換器： A/D 16x10b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 80-TQFP
包裝： 托盤
配用： DM300019-ND - BOARD DEMO DSPICDEM 80L STARTER
AC164314-ND - MODULE SKT FOR PM3 80PF
DM300020-ND - BOARD DEV DSPICDEM MC1 MOTORCTRL
其它名稱： DSPIC30F601020EPF
dsPIC30F6010
DS70119E-page 76
2006 Microchip Technology Inc.
13.1
Timer2 and Timer3 Selection Mode
Each output compare channel can select between one
of two 16-bit timers; Timer2 or Timer3.
The selection of the timers is controlled by the OCTSEL
bit (OCxCON<3>). Timer2 is the default timer resource
for the Output Compare module.
13.2
Simple Output Compare Match
Mode
When control bits OCM<2:0> (OCxCON<2:0>) = 001,
010
or 011, the selected output compare channel is
configured for one of three simple output compare
match modes:
Compare forces I/O pin low
Compare forces I/O pin high
Compare toggles I/O pin
The OCxR register is used in these modes. The OCxR
register is loaded with a value and is compared to the
selected incrementing timer count. When a compare
occurs, one of these compare match modes occurs. If
the counter resets to zero before reaching the value in
OCxR, the state of the OCx pin remains unchanged.
13.3
Dual Output Compare Match Mode
When control bits OCM<2:0> (OCxCON<2:0>) = 100
or 101, the selected output compare channel is config-
ured for one of two dual output compare modes, which
are:
Single Output Pulse mode
Continuous Output Pulse mode
13.3.1
SINGLE PULSE MODE
For the user to configure the module for the generation
of a single output pulse, the following steps are
required (assuming timer is off):
Determine instruction cycle time TCY.
Calculate desired pulse width value based on TCY.
Calculate time to start pulse from timer start value
of 0x0000.
Write pulse width start and stop times into OCxR
and OCxRS compare registers (x denotes
channel 1, 2, ...,N).
Set timer period register to value equal to, or
greater than, value in OCxRS compare register.
Set OCM<2:0> = 100.
Enable timer, TON (TxCON<15>) = 1.
To initiate another single pulse, issue another write to
set OCM<2:0> = 100.
13.3.2
CONTINUOUS PULSE MODE
For the user to configure the module for the generation
of a continuous stream of output pulses, the following
steps are required:
Determine instruction cycle time TCY.
Calculate desired pulse value based on TCY.
Calculate timer to start pulse width from timer start
value of 0x0000.
Write pulse width start and stop times into OCxR
and OCxRS (x denotes channel 1, 2, ...,N)
compare registers, respectively.
Set timer period register to value equal to, or
greater than, value in OCxRS compare register.
Set OCM<2:0> = 101.
Enable timer, TON (TxCON<15>) = 1.
13.4
Simple PWM Mode
When control bits OCM<2:0> (OCxCON<2:0>) = 110
or 111, the selected output compare channel is config-
ured for the PWM mode of operation. When configured
for the PWM mode of operation, OCxR is the Main latch
(read only) and OCxRS is the Secondary latch. This
enables glitchless PWM transitions.
The user must perform the following steps in order to
configure the output compare module for PWM
operation:
1.
Set the PWM period by writing to the appropriate
period register.
2.
Set the PWM duty cycle by writing to the OCxRS
register.
3.
Configure the output compare module for PWM
operation.
4.
Set the TMRx prescale value and enable the
Timer, TON (TxCON<15>) = 1.
13.4.1
INPUT PIN FAULT PROTECTION
FOR PWM
When control bits OCM<2:0> (OCxCON<2:0>) = 111,
the selected output compare channel is again config-
ured for the PWM mode of operation, with the addi-
tional feature of input fault protection. While in this
mode, if a logic ‘0’ is detected on the OCFA/B pin, the
respective PWM output pin is placed in the high imped-
ance input state. The OCFLT bit (OCxCON<4>) indi-
cates whether a Fault condition has occurred. This
state will be maintained until both of the following
events have occurred:
The external Fault condition has been removed.
The PWM mode has been re-enabled by writing
to the appropriate control bits.
相關PDF資料
PDF描述
DSPIC30F6010A-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6013A-30I/PF IC DSPIC MCU/DSP 132K 80TQFP
DSPIC30F6014-30I/PF IC DSPIC MCU/DSP 144K 80TQFP
DSPIC33EP512MU814-I/PL IC DSC 16BIT 512KB 144LQFP
DSPIC33EP64MC504-E/TL IC DSC 16BIT 64KB FLASH 44-VTLA
相關代理商/技術參數
參數描述
DSPIC30F6010-20I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 20MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6010-20I/PF 制造商:Microchip Technology Inc 功能描述:16BIT 20MIPS DSPIC SMD 30F6010
DSPIC30F6010-30I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 30MHz 144KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6010-30I/PF 制造商:Microchip Technology Inc 功能描述:16BIT 30MIPS DSPIC SMD 30F6010
DSPIC30F6010-30I/PF 制造商:Microchip Technology Inc 功能描述:Digital Signal Processor IC Frequency Ma
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*