- 您現在的位置：買賣IC網 > PDF目錄377002 > DSPE56007FJ88 DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC PDF資料下載
參數資料
| 型號： | DSPE56007FJ88 |
| 英文描述： | DSP|24-BIT|CMOS|QFP|80PIN|PLASTIC |
| 中文描述： | 數字信號處理器| 24位|的CMOS | QFP封裝| 80腳|塑料 |
| 文件頁數： | 22/83頁 |
| 文件大?。?/td> | 382K |
| 代理商： | DSPE56007FJ88 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
1-16
DSP56007/D
MOTOROLA
Signal/Connection Descriptions
General Purpose I/O
GENERAL PURPOSE I/O
ON-CHIP EMULATION (OnCE
TM
) PORT
There are four signals associated with the OnCE port controller and its serial
interface.
Table 1-11
General Purpose I/ O (GPIO) Signals
Signal
Name
Signal
Type
State during
Reset
Signal Description
GPIO0–
GPIO3
Standard
Output,
Open-drain
Output, or
Input
Disconnected
GPIO lines can be used for control and handshake
functions between the DSP and external circuitry.
Each GPIO line can be configured individually as
disconnected, open-drain output, standard output,
or an input.
Note:
Hardware reset or software reset configures all
the GPIO lines as disconnected (external
circuitry connected to these pins may need pull-
ups until the pins are configured for operation).
Table 1-12
On-Chip Emulation Port Signals
Signal
Name
Signal
Type
State during
Reset
Signal Description
DSI
OS0
Input
Output
Output,
Driven Low
Debug Serial Input (DSI)
—The DSI signal is the signal
through which serial data or commands are provided to the
OnCE port controller. The data received on the DSI signal
will be recognized only when the DSP has entered the
Debug mode of operation. Data must have valid TTL logic
levels before the serial clock falling edge. Data is always
shifted into the OnCE port Most Significant Bit (MSB) first.
Operating Status 0 (OS0)—
When the DSP is not in the Debug
mode, the OS0 signal provides information about the DSP
status if it is an output and used in conjunction with the OS1
signal. When switching from output to input, the signal is
tri-stated.
Note:
If the OnCE port is in use, an external pull-down resistor
should be attached to the DSI/ OS0 signal. If the OnCE
port is not in use, the resistor is not required.
相關PDF資料 |
PDF描述 |
|---|---|
| DSPCOMMANDUM | Universal Command Converter for DSP User＇s Manual |
| DSPCOMMPARALLELUM | Parallel Port Command Converter for DSP User＇s Manual |
| DSPCOMMPCIUM | PCI Command Converter for DSP User＇s Manual |
| DSPG4001-71 | Telecommunication IC |
| DSPG5002 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPF3-S7-120V | 制造商:Black Box Corporation 功能描述:DIGITAL SIGNAGE POWER FILTER |
| DSPF3-S7-120V-W1 | 制造商:Black Box Corporation 功能描述:1 YEAR WARRANTY FOR DSPF3-S7-120V |
| DSPF3-S7-120V-W3 | 制造商:Black Box Corporation 功能描述:3 YEAR WARRANTY FOR DSPF3-S7-120V |
| DSPF56362PV100 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| DSPFPK52 | 制造商:BARRY CONTROLS/VLIER 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。