參數資料
型號： DS2407V
英文描述： Dual Addressable Switch Plus 1K.Bit Memory
中文描述： 雙尋址開關與1K.Bit記憶
文件頁數： 27/31頁
文件大?。?/td> 194K
代理商： DS2407V
DS2407
012099 27/31
When reading the data memory of the DS2407 with the
Extended Read Memory command, there are two situa-
tions where a 16–bit CRC is transmitted. One 16–bit
CRC follows each Redirection Byte, another 16–bit
CRC is received after the last byte of a memory data
page is read. The CRC at the end of the memory page is
always the result of clearing the CRC generator and
shifting in the data bytes beginning at the first addressed
memory location of the EPROM data page until the last
byte of this page. With the initial pass through the
Extended Read Memory flow chart the 16–bit CRC
value is the result of shifting the command byte into the
cleared CRC generator, followed by the two address
bytes and the Redirection Byte. Subsequent passes
through the Extended Read Memory flow chart will gen-
erate a 16–bit CRC that is the result of clearing the CRC
generator and then shifting in only the Redirection Byte.
When writing to the DS2407 (either data memory or Sta-
tus Memory), the bus master receives a 16–bit CRC to
verify that the data transfer was correct before applying
the programming pulse. With the initial pass through the
Write Memory/Status flow chart the 16–bit CRC will be
generated by clearing the CRC–generator, shifting in
the command, low address, high address and the data
byte. Subsequent passes through the Write Memory/
Status flow chart due to the DS2407 automatically incre-
menting its address counter will generate a 16–bit CRC
that is the result of loading (not shifting) the new
(incremented) address into the CRC generator and then
shifting in the new data byte.
When communicating with a PIO channel using the
Channel Access command, one can select if and how
often a 16–bit CRC will be added to the data stream.
This CRC selection is specified in the Channel Control
byte 1 and may be different every time the Channel
Access command is issued by the bus master. Depend-
ing on the CRC selection, the device can generate a
CRC after every byte that follows the Channel Info byte,
after each block of eight bytes or after each block of 32
bytes. If the CRC is enabled, with the initial pass through
the Channel Access flow chart the 16–bit CRC will be
generated by clearing the CRC–generator, shifting in
the command, Channel Control Bytes 1 and 2, Channel
Info Byte and the specified amount of data bytes (1, 8 or
32). Subsequent passes through the Channel Access
flow chart will generate a 16–bit CRC that is the result of
clearing the CRC generator and then shifting in the new
data bytes. This algorithm is valid for all accesses to the
PIO channels, continuous reading or writing as well as
toggling between read and write.
The comparison of CRC values and decision to con-
tinue with an operation are determined entirely by the
bus master. There is no circuitry on the DS2407 that pre-
vents a command sequence from proceeding if the CRC
stored in or calculated by the DS2407 does not match
the value generated by the bus master. For more details
on generating CRC values including example imple-
mentations in both hardware and software, see the
“Book of DS19xx iButton Standards”.
PROGRAM PULSE TIMING DIAGRAM
Figure 16
>5
μ
s
LINE TYPE LEGEND:
V
PULLUP
GND
V
PP
>5
μ
s
480
μ
s
NORMAL 1–Wire
COMMUNICATION ENDS
NORMAL 1–Wire
COMMUNICATION RESUMES
Bus master active high
(12V @ 10 mA)
t
RP
t
FP
t
DP
t
DV
Resistor pull–up
t
PP
相關PDF資料
PDF描述
DS2407X Dual Addressable Switch Plus 1K.Bit Memory
DS2417X 1-Wire Time Chip With Interrupt
DS2417 1-Wire Time Chip With Interrupt
DS2417P 1-Wire Time Chip With Interrupt
DS2417V 1-Wire Time Chip With Interrupt
相關代理商/技術參數
參數描述
DS2407X 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Dual Addressable Switch Plus 1K.Bit Memory
DS2408 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 8-Channel Addressable Switch
DS2408_10 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 8-Channel Addressable Switch
DS2408S 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
DS2408S/R 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:1-Wire 8-Channel Addressable Switch
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*