參數資料
型號： DS21Q44T
元件分類： 通信及網絡
英文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
中文描述： Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0
文件頁數： 18/105頁
文件大?。?/td> 620K
代理商： DS21Q44T
DS21Q44
18 of 105
Signal Name:
Signal Description:
Signal Type:
Strap high to select Motorola bus timing; strap low to select Intel bus timing. This pin controls the
function of the RD*(DS*), ALE(AS), and WR*(R/W*) pins. If BTS = 1, then these pins assume the
function listed in parenthesis ().
BTS
Bus Type Select
Input
Signal Name:
Signal Description:
Signal Type:
RD* and DS* are active low signals. Note: DS is active high when MUX=1. Refer to bus timing
diagrams in section 19 .
RD* (DS*)
Read Input (Data Strobe)
Input
Signal Name:
Signal Description:
Signal Type:
Selects which of the four framers to be accessed.
FS0 AND FS1
Framer Selects
Input
Signal Name:
Signal Description:
Signal Type:
Must be low to read or write to the device. CS* is an active low signal.
CS*
Chip Select
Input
Signal Name:
Signal Description:
Signal Type:
WR* is an active low signal.
WR* (R/W*)
Write Input (Read/Write)
Input
TEST ACCESS PORT PINS
Signal Name:
Signal Description:
Signal Type:
Set high to 3–state all output and I/O pins (including the parallel control port). Set low for normal
operation. Useful in board level testing.
TEST
3–State Control
Input
Signal Name:
Signal Description:
Signal Type:
This signal is used to asynchronously reset the test access port controller. At power up, JTRST* must be
set low and then high. This action will set the device into the boundary scan bypass mode allowing
normal device operation. If boundary scan is not used, this pin should be held low. This function is
available when FMS = 0.
JTRST*
IEEE 1149.1 Test Reset
Input
Signal Name:
Signal Description:
Signal Type:
This pin is sampled on the rising edge of JTCLK and is used to place the test port into the various defined
IEEE 1149.1 states. If not used, this pin should be pulled high. This function is available when FMS = 0.
JTMS
IEEE 1149.1 Test Mode Select
Input
相關PDF資料
PDF描述
DS21Q44TN MICROSWITCH, SPDT, SIM ROLLER LEVER; Current, contact AC:5A; Force, operating:91.75gf; Travel, pre:16.0mm; Centres, fixing LxW:22.2mm; Temp, op. max:120(degree C); Temp, op. min:-40(degree C); Length / Height, external:9.25mm; Width, RoHS Compliant: Yes
DS2251T-128-16 CONNECTOR ACCESSORY
DS2251T-32-16 128k Soft Microcontroller Module
DS2251T-64-16 CONNECTOR ACCESSORY
DS2251 128k Soft Microcontroller Module
相關代理商/技術參數
參數描述
DS21Q44T+ 功能描述:網絡控制器與處理器 IC Enhanced Quad E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q44TN 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q48 功能描述:網絡控制器與處理器 IC 5V Quad E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q48A3N 功能描述:網絡控制器與處理器 IC 5V Quad E1/T1/J1 Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q48B 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*