參數資料
型號： DS2196LN
廠商： DALLAS SEMICONDUCTOR
元件分類： Digital Transmission Controller
英文描述： DATACOM, FRAMER, PQFP100
封裝： LQFP-100
文件頁數： 6/160頁
文件大?。?/td> 559K
代理商： DS2196LN
DS2196
103 of 160
Four new registers were added for the enhanced functionality of the HDLC controller; RDC1, RDC2,
TDC1, and TDC2. Note that the BOC controller is functional when the HDLC controller is used for
DS0s. Section 18 contains all of the HDLC and BOC registers and information on FDL/Fs Extraction and
Insertion with and without the HDLC controller.
17.1 HDLC FOR DS0S
When using the HDLC controllers for DS0s, the same registers shown in section 18 will be used except
for the TBOC and RBOC registers and bits HCR.7, HSR.7, and HIMR.7.
As a basic guideline for interpreting and sending HDLC messages and BOC messages, the following
sequences can be applied.
Receive a HDLC Message
1. Enable RPS interrupts
2. Wait for interrupt to occur
3. Disable RPS interrupt and enable either RPE, RNE, or RHALF interrupt
4. Read RHIR to obtain REMPTY status
a. If REMPTY=0, then record OBYTE, CBYTE, and POK bits and then read the FIFO
a1. if CBYTE=0 then skip to step 5
a2. if CBYTE=1 then skip to step 7
b. If REMPTY=1, then skip to step 6
5. Repeat step 4
6. Wait for interrupt, skip to step 4
7. If POK=0, then discard whole packet, if POK=1, accept the packet
8. Disable RPE, RNE, or RHALF interrupt, enable RPS interrupt and return to step 1.
Transmit a HDLC Message
1. Make sure HDLC controller is done sending any previous messages and is current sending flags by
checking that the FIFO is empty by reading the TEMPTY status bit in the THIR register
2. Enable either the THALF or TNF interrupt
3. Read THIR to obtain TFULL status
a. If TFULL=0, then write a byte into the FIFO and skip to next step (special case occurs when
the last byte is to be written, in this case set TEOM=1 before writing the byte and then skip to
step 6)
b. If TFULL=1, then skip to step 5
4. Repeat step 3
5. Wait for interrupt, skip to step 3
6. Disable THALF or TNF interrupt and enable TMEND interrupt
7. Wait for an interrupt, then read TUDR status bit to make sure packet was transmitted correctly.
相關PDF資料
PDF描述
DS21FF44 DATACOM, FRAMER, PBGA300
DS21FF44N DATACOM, FRAMER, PBGA300
DS21FT40N DATACOM, FRAMER, PBGA300
DS21FT40 DATACOM, FRAMER, PBGA300
DS21FT42 DATACOM, FRAMER, PBGA300
相關代理商/技術參數
參數描述
DS2196LN+ 功能描述:網絡控制器與處理器 IC T1 Dual Framer LIU RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS219T 功能描述:烙鐵 DESOLDERING HEAD RoHS:否 制造商:Weller 產品:Soldering Stations 類型:Digital, Iron, Stand, Cleaner 瓦特:50 W 最大溫度:+ 850 F 電纜類型:US Cord Included
DS21E352 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E352N 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21E354 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*