參數資料
型號： DM9102DE
廠商： Electronic Theatre Controls, Inc.
英文描述： SINGLE CHIP FAST ETHEMET NIC CONTROLLER
中文描述： 單晶片快速以太網NIC控制器
文件頁數： 33/70頁
文件大?。?/td> 2245K
代理商： DM9102DE
Preliminary datasheet
Version: DM9102D-DS-P02
Jan. 14, 2005
33
6.3.1
Basic Mode Control Register (BMCR) – 0
Bit
Name
15
Reset
Default
0, RW/SC Reset:
Description
1=Software reset
0=Normal operation
This bit resets the status and controls the PHY registers of the DM9102D to
their default states. This bit, which is self-clearing, will keep its value until the
reset process is completed
Loopback:
1=Loop-back enabled
0=Normal operation
When in 100Mbps operation mode, setting this bit may cause the
descrambler to lose synchronization and produce a 720ms "dead time" before
any valid data to the MAC.
Speed Select:
1=100Mbps
0=10Mbps
Link speed may be selected either by this bit or by Auto-negotiation. When
Auto-negotiation is enabled and bit 12 is set, this bit will reflect Auto-
negotiation selected media type.
Auto-negotiation Enable:
1= Auto-negotiation enabled: bit 8 and 13 will report Auto-negotiation status
0= Auto-negotiation disabled: bit 8 and 13 will determine the link speed and
duplex mode
Power Down:
Setting this bit will power down the internal PHY except crystal / oscillator
circuit.
1=Power Down
0=Normal Operation
Reserved.
Write as 0, ignore on read.
0,RW/SC Restart Auto-negotiation:
1= Restart Auto-negotiation. Re-initiates the Auto-negotiation process. When
Auto-negotiation is disabled (bit 12 of this register cleared), this bit has no
function and it should be cleared. This bit is self-clearing and it will keep
its value until Auto-negotiation is initiated by the DM9102D. The operation of
the
Auto-negotiation
process
management entity that clears this bit.
0= Normal Operation
1,RW
Duplex Mode:
1= Full Duplex operation. Duplex selection is allowed when Auto-negotiation is
disabled (bit 12 of this register is cleared). With Auto-negotiation enabled, this
bit reflects the duplex capability selected by Auto-negotiation.
0= Normal operation
0,RW
Collision Test:
1= Collision Test enabled. When set in half duplex mode, the DM9102D will
enter collision state if packet transmission is in progress.
0= Normal Operation
<0000000>,
RO
14
Loopback
0, RW
13
Speed Selection
1, RW
12
Auto-negotiation
Enable
1, RW
11
Power Down
0, RW
10
Reserved
0,RO
9
Restart
Auto-negotiation
will
not
be
affected
by
the
8
Duplex Mode
7
Collision Test
6:0
Reserved
Reserved. Write as 0, ignore on read
6.3.2 Basic Mode Status Register (BMSR) – 1
相關PDF資料
PDF描述
DM9102 Single Chip Fast Ethernet NIC controller
DM9102A Single Chip Fast Ethernet NIC controller
DM9102AF Single Chip Fast Ethernet NIC controller
DM9102AT Single Chip Fast Ethernet NIC controller
DM9108APPLICATIONENGINEERINGNOTESONE DM9108 Application Engineering notes one
相關代理商/技術參數
參數描述
DM9102DEP 制造商:DAVICOM 功能描述:IC ENET CNTRL 10/100M PHY 1 制造商:DAVICOM 功能描述:IC ENET CNTRL 10/100M PHY 128LQFP 制造商:DAVICOM 功能描述:IC, ENET CNTRL, 10/100M PHY, 128LQFP 制造商:DAVICOM 功能描述:IC, ENET CNTRL, 10/100M PHY, 128LQFP; Data Rate:100Mbps; Ethernet Type:IEEE 802.3u; Supply Voltage Min:2.375V; Supply Voltage Max:2.625V; Digital IC Case Style:LQFP; No. of Pins:128; Interface Type:PCI; Operating Temperature Min:0C;;RoHS Compliant: Yes
DM9102H 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:Single Chip Fast Ethernet NIC Controller
DM9102HEP 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:Single Chip Fast Ethernet NIC Controller
DM9103 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:10/100 Mbps 3-port Ethernet Switch Controller with PCI Interface
DM9103EP 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:Three Port Ethernet Switch Controller with PCI Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*