- 您現在的位置：買賣IC網 > PDF目錄380227 > CYV15G0204TRB (Cypress Semiconductor Corp.) Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer PDF資料下載
參數資料
| 型號： | CYV15G0204TRB |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer |
| 中文描述： | 獨立時鐘的HOTLink二⑩雙串行解串器和雙時鐘重計 |
| 文件頁數： | 9/31頁 |
| 文件大小： | 389K |
| 代理商： | CYV15G0204TRB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
CYV15G0204TRB
Document #: 38-02101 Rev. *C
Page 9 of 31
Receive Path Data and Status Signals
RXDC[9:0]
RXDD[9:0]
LVTTL Output,
synchronous to the
RXCLK± output
Parallel Data Output
. RXDx[9:0] parallel data outputs change relative to the receive
interface clock. If RXCLKx± is a full-rate clock, the RXCLKx± clock outputs are
complementary clocks operating at the character rate. The RXDx[9:0] outputs for the
associated receive channels follow rising edge of RXCLKx+ or falling edge of
RXCLKx–. If RXCLKx± is a half-rate clock, the RXCLKx± clock outputs are comple-
mentary clocks operating at half the character rate. The RXDx[9:0] outputs for the
associated receive channels follow both the falling and rising edges of the associated
RXCLKx± clock outputs.
When BIST is enabled on the receive channel, the BIST status is presented on the
RXDx[1:0] and BISTSTx outputs. See
Table 6 on page 19
for each status reported
by the BIST state machine. Also, while BIST is enabled, the RXDx[9:2] outputs
should be ignored.
BIST Status Output.
When RXBISTx[1:0] = 10, BISTSTx (along with RXDx[1:0])
displays the status of the BIST reception. See
Table 6 on page 19
for the BIST status
reported for each combination of BISTSTx and RXDx[1:0].
When RXBISTx[1:0]
≠
10, BISTSTx should be ignored.
Reclocker Powered Down Status Output.
REPDOx is asserted HIGH, when the
associated channel’s reclocker output logic is powered down. This occurs when
ROE2x and ROE1x are both disabled by setting ROE2x = 0 and ROE1x = 0.
BISTSTC
BISTSTD
LVTTL Output,
synchronous to the
RXCLKx ± output
REPDOC
REPDOD
Asynchronous to
reclocker output
channel
enable / disable
Receive Path Clock Signals
TRGCLKC±
TRGCLKD±
Differential LVPECL
or single-ended
LVTTL input clock
CDR PLL Training Clock
. TRGCLKx± clock inputs are used as the reference source
for the frequency detector (Range Controller) of the associated receive PLL to
reduce PLL acquisition time.
In the presence of valid serial data, the recovered clock output of the receive CDR
PLL (RXCLKx±) has no frequency or phase relationship with TRGCLKx±.
When driven by a single-ended LVCMOS or LVTTL clock source, connect the clock
source to either the true or complement TRGCLKx input, and leave the alternate
TRGCLKx input open (floating). When driven by an LVPECL clock source, the clock
must be a differential clock, using both inputs.
LVTTL Output Clock
Receive Clock Output
. RXCLKx± is the receive interface clock used to control
timing of the RXDx[9:0] parallel outputs. These true and complement clocks are used
to control timing of data output transfers. These clocks are output continuously at
either the half-character rate (1/20
th
the serial bit-rate) or character rate (1/10
th
the
serial bit-rate) of the data being received, as selected by RXRATEx.
LVTTL Output
Reclocker Clock Output
. RECLKOx output clock is synthesized by the associated
reclocker output PLL and operates synchronous to the internal recovered character
clock. RECLKOx operates at either the same frequency as RXCLKx± (RXRATEx =
0), or at twice the frequency of RXCLKx± (RXRATEx = 1).The reclocker clock outputs
have no fixed phase relationship to RXCLKx±.
Device Control Signals
RESET
LVTTL Input,
asynchronous,
internal pull-up
for a minimum pulse width. When the reset is removed, all state machines, counters
and configuration latches are at an initial state. As per the JTAG specifications the
device RESET cannot reset the JTAG controller. Therefore, the JTAG controller has
to be reset separately. Refer to
“JTAG Support” on page 19
for the methods to reset
the JTAG state machine. See
Table 4 on page 16
for the initialize values of the device
configuration latches.
RXCLKC±
RXCLKD±
RECLKOC
RECLKOD
Asynchronous Device Reset
. RESET initializes all state machines, counters, and
configuration latches in the device to a known state. RESET must be asserted LOW
Pin Definitions
(continued)
CYV15G0204TRB HOTLink II Dual Serializer and Dual Reclocking Deserializer
Name
I/O Characteristics
Signal Description
[+] Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| CYV15G0204TRB-BGC | Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer |
| CYV15G0204TRB-BGXC | Independent Clock HOTLink II⑩ Dual Serializer and Dual Reclocking Deserializer |
| CYV15G0401DXB | Quad HOTLink II Transceiver |
| CYV15G0401DXB-BGC | Quad HOTLink II Transceiver |
| CYV15G0401DXB-BGI | Quad HOTLink II Transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYV15G0204TRB-BGC | 功能描述:視頻 IC 2x Indep Reclocker Serializer COM RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CYV15G0204TRB-BGXC | 功能描述:視頻 IC 2x Indep Reclocker Serializer COM RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| CYV15G0401DXB | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Quad HOTLink II⑩ Transceiver |
| CYV15G0401DXB-BGC | 功能描述:電信線路管理 IC Quad Ch Video COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| CYV15G0401DXB-BGI | 功能描述:電信線路管理 IC Quad Ch Video COM RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。