- 您現在的位置：買賣IC網 > PDF目錄380224 > CYP15G0402DX-BGC (CYPRESS SEMICONDUCTOR CORP) Quad HOTLinkII SERDES PDF資料下載
參數資料
| 型號： | CYP15G0402DX-BGC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 通信及網絡 |
| 英文描述： | Quad HOTLinkII SERDES |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PBGA256 |
| 封裝： | 27 X 27 MM, 1.52 MM HEIGHT, THERMALLY ENHANCED, BGA-256 |
| 文件頁數： | 15/27頁 |
| 文件大?。?/td> | 852K |
| 代理商： | CYP15G0402DX-BGC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
CYP15G0402DX
PRELIMINARY
Document #: 38-02023 Rev. *B
Page 15 of 27
channels will save considerable power and will reduce system
heat generation. Controlling system power dissipation will
improve the system reliability.
Receive Channel Power-Control Latch Enable. Active HIGH.
When RXLE is HIGH, the signals on the BOE[7:0] inputs
directly control the power enables for the receive PLLs and
analog circuits. When the BOE[7:0] input is HIGH, the
associated receive channel [A.D] PLLs and analog logic are
active. When the BOE[7:0] input is LOW, the associated
receive channel [A.D] PLL
’
s and analog circuits are in a power
down mode. When RXLE returns LOW, the last values present
on BOE[7:0] are captured. The channels controlled by
BOE[7:0] signals are listed in
Table 2
.
When RXLE is HIGH and BOE[x] is HIGH, the associated
receive channel is enabled to receive a serial stream from the
selected line receiver. When RXLE is HIGH and BOE[x] is
LOW, the associated receive channel is disabled and powered
down.
Any disabled channel will indicate a constant /LFIx output.
When a disabled receive channel is re-enabled, the status of
the associated LFIx output and data on the parallel outputs for
the associated channel may be indeterminate for up to 10 ms.
After powering the chip, the Transmitter may assume either a
positive or negative value for its initial running disparity. Upon
transmission of any Transmission Character, the transmitter
will select the proper version of the Transmission Character
When OELE is HIGH and BOE[x] is HIGH, the associated
serial driver is enabled. When OELE is HIGH and BOE[x] is
LOW, the associated driver is disabled and powered down. If
both outputs for a channel are disabled, the internal logic for
that channel is powered down. When OELE returns LOW, the
values present on the BOE[7:0] inputs are latched in the
Output Enable Latch.
Output Bus
Each receive channel presents a 12-signal output bus
consisting of:
a 10-bit data bus
a COMMA detect indicator
a parity bit.
The receive decoder assigns the bit values per
Table 7
.
The externally encoded data, the RXDx[0] corresponds to the
MSB of the 10 bit data. The signals present on this output bus
are shown in
Table 8
.
The framed 10-bit value is presented to the associated Output
Register, along with a status output indicating if the character
in the output register matches the selected framing characters.
The COMDETx status outputs operate the same regardless of
the bit combination selected for character framing by the
FRAMCHAR input. Characters in
Table 5
will cause COMDET
assertion, all others characters are mapped to invalid
characters. COMDETx is HIGH when the character in the
output register of the associated channel contains the selected
framing character at the proper character boundary, and LOW
for all other bit combinations.
When the low-latency framer and half-rate receive port
clocking are enabled, RFMODE and RXRATE are both LOW,
the framer will stretch the recovered clock to the next 20-bit
boundary such that the rising edge of RXCLKx+ occurs when
COMDET is present on the associated output bus.
When the standard framer is enabled and half-rate receive
port clocking are enabled, RFMODE is not low and RXRATE
is LOW, the output clock is not modified, but a single pipeline
stage may be added or subtracted from the data stream by the
framer logic such that the rising edge of RXCLKx+ occurs
when COMDET is present on the associated output bus.
This adjustment only occurs when the framer for that channel
is enabled (RFENx is HIGH). When the framer is disabled, the
Table 7. Output Register Bit Assignments
[4]
Signal Name
RXSTx[2]
(LSB)
COMDETx
RXSTx[1]
DOUTx[0]
RXSTx[0]
DOUTx[1]
RXDx[0]
DOUTx[2]
RXDx[1]
DOUTx[3]
RXDx[2]
DOUTx[4]
RXDx[3]
DOUTx[5]
RXDx[4]
DOUTx[6]
RXDx[5]
DOUTx[7]
RXDx[6]
DOUTx[8]
RXDx[7]
(MSB)
DOUTx[9]
Note:
4.
The RXOPx outputs are also driven from the associated output reg-
ister, but their interpretation is under the separate control of PARCTL.
Table 8. Output Register Bit Assignments
Signal Name
RXOPx
[5]
COMDET
[5]
Bus Weight
10B Name
RXDx[0]
(LSB)
2
0
a
[6]
RXDx[1]
2
1
2
2
b
RXDx[2]
c
RXDx[3]
2
3
d
RXDx[4]
2
4
2
5
e
RXDx[5]
i
RXDx[6]
2
6
f
RXDx[7]
2
7
2
8
g
RXDx[8]
h
RXDx[9]
(MSB)
2
9
j
5.
The RXOPx and COMDETx outputs are also driven from the associated
output register, but their generation and interpretation are separate from
the data bus.
LSB will be shifted in first.
6.
相關PDF資料 |
PDF描述 |
|---|---|
| CYP15G0402DX | Quad HOTLinkII SERDES |
| CYP15G0402DX-BGI | Quad HOTLinkII SERDES |
| CYP15G0402DXB | Quad HOTLink II SERDES(四HOTLink II并行轉換器) |
| CYV15G0402DXB | Quad HOTLink II SERDES(四HOTLink II并行轉換器) |
| CYP15G0403DXB | Independent Clock Quad HOTLink II Transceiver(獨立時鐘，四熱連接II收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CYP15G0402DX-BGI | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Quad HOTLinkII SERDES |
| CYP15G0402DX-EVAL | 功能描述:界面開發工具 Quad Ch HOTLink II GbE 1XFC SERDES RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| CYP15G0403DXB | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II Transceiver Single 3.3V supply |
| CYP15G0403DXB_07 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II⑩ Transceiver |
| CYP15G0403DXB_09 | 制造商:CYPRESS 制造商全稱:Cypress Semiconductor 功能描述:Independent Clock Quad HOTLink II Transceiver |
發布緊急采購，3分鐘左右您將得到回復。