- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C63231A (Cypress Semiconductor Corp.) enCoRe USB Low-speed USB Peripheral Controller(enCoRe USB 低速USB外設控制器) PDF資料下載
參數資料
| 型號： | CY7C63231A |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | enCoRe USB Low-speed USB Peripheral Controller(enCoRe USB 低速USB外設控制器) |
| 中文描述： | 的enCoRe USB低速USB外設控制器（的enCoRe的USB低速的USB外設控制器） |
| 文件頁數： | 26/50頁 |
| 文件大?。?/td> | 1036K |
| 代理商： | CY7C63231A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
FOR
FOR
enCoRe
USB
CY7C63221/31A
Document #: 38-08028 Rev. *B
Page 26 of 50
While this bit is set to ‘1’, the CPU cannot write to the EP0 FIFO. This prevents firmware from overwriting an incoming SETUP
transaction before firmware has a chance to read the SETUP data.
0 = No SETUP received. This bit is cleared by any non-locked writes to the register.
Bit 6: IN Received
1 = A valid IN packet has been received. This bit is updated to ‘1’ after the last received packet in an IN transaction. This bit
is cleared by any non-locked writes to the register.
0 = No IN received. This bit is cleared by any non-locked writes to the register.
Bit 5: OUT Received
1 = A valid OUT packet has been received. This bit is updated to ‘1’ after the last received packet in an OUT transaction. This
bit is cleared by any non-locked writes to the register.
0 = No OUT received. This bit is cleared by any non-locked writes to the register.
Bit 4: ACKed Transaction
The ACKed Transaction bit is set whenever the SIE engages in a transaction to the register's endpoint that completes with an
ACK packet.
1 = The transaction completes with an ACK
0 = The transaction does not complete with an ACK
Bit [3:0]: Mode Bit[3:0]
The endpoint modes determine how the SIE responds to USB traffic that the host sends to the endpoint. For example, if the
endpoint Mode Bits [3:0] are set to 0001 which is NAK IN/OUT mode as shown in
Table 20-1
, the SIE will send NAK hand-
shakes in response to any IN or OUT token sent to this endpoint. In this NAK IN/OUT mode, the SIE will send an ACK
handshake when the host sends a SETUP token to this endpoint. The mode encoding is shown in
Table 20-1
. Additional
information on the mode bits can be found in
Table 20-2
and
Table 20-3
. These modes give the firmware total control on how
to respond to different tokens sent to the endpoints from the host.
In addition, the Mode Bits are automatically changed by the SIE in response to many USB transactions. For example, if the
Mode Bit [3:0] are set to 1011 which is ACK OUT-NAK IN mode as shown in
Table 20-1
, the SIE will change the endpoint Mode
Bit [3:0] to NAK IN/OUT (0001) mode after issuing an ACK handshake in response to an OUT token. Firmware needs to update
the mode for the SIE to respond appropriately.
14.3
The feature one non-control endpoint, endpoint 1 (EP1). The EP1 Mode Register does not have the locking mechanism of the
EP0 Mode Register. The EP1 Mode Register uses the format shown in
Figure 14-3
. EP1 uses an 8-byte FIFO at SRAM locations
0xF0–0xF7 as shown in Section 8.2.
USB Non-Control Endpoints
Bit 7: STALL
1 = The SIE will stall an OUT packet if the Mode Bits are set to ACK-OUT, and the SIE will stall an IN packet if the mode bits
are set to ACK-IN. See Section 20.0 for the available modes.
0 = This bit must be set to LOW for all other modes.
Bit [6:5]:
Reserved. Must be written to zero during register writes.
Bit 4: ACKed Transaction
The ACKed transaction bit is set whenever the SIE engages in a transaction to the register's endpoint that completes with an
ACK packet.
1 = The transaction completes with an ACK.
0 = The transaction does not complete with an ACK.
Bit #
7
6
5
4
3
2
1
0
Bit Name
STALL
Reserved
ACKed
Transaction
Mode Bit
Read/Write
R/W
-
-
R/C
R/W
R/W
R/W
R/W
Reset
0
0
0
0
0
0
0
0
Figure 14-3. USB Endpoint EP1 Mode Registers (Address 0x14)
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C64013C | Full-Speed USB (12-Mbps)(全速USB(12-Mbps)) |
| CY7C64113C | Full-Speed USB (12-Mbps)(全速USB(12-Mbps)) |
| CY7C64013 | Full-Speed USB (12 Mbps) Function(全速 USB (12 Mbps)性能) |
| CY7C64113 | Full-Speed USB (12 Mbps) Function(全速 USB (12 Mbps)性能) |
| CY7C64713 | EZ-USB FX1 USB Microcontroller Full-speed USB Peripheral Controller(EZ-USB FX1 USB微控制器，全速USB外設控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C63231A-PXC | 功能描述:8位微控制器 -MCU enCoRe RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C63231A-SC | 功能描述:IC MCU 3K USB LS PERIPH 18-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63231A-SXC | 功能描述:8位微控制器 -MCU enCoRe RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C63231A-SXCT | 功能描述:IC MCU 3K USB LS PERIPH 18-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63310-PXC | 功能描述:USB 接口集成電路 USB 3K Flash 128 byte RAM COM RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。