- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C63231A (Cypress Semiconductor Corp.) enCoRe USB Low-speed USB Peripheral Controller(enCoRe USB 低速USB外設控制器) PDF資料下載
參數資料
| 型號： | CY7C63231A |
| 廠商： | Cypress Semiconductor Corp. |
| 英文描述： | enCoRe USB Low-speed USB Peripheral Controller(enCoRe USB 低速USB外設控制器) |
| 中文描述： | 的enCoRe USB低速USB外設控制器（的enCoRe的USB低速的USB外設控制器） |
| 文件頁數： | 15/50頁 |
| 文件大?。?/td> | 1036K |
| 代理商： | CY7C63231A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
FOR
FOR
enCoRe
USB
CY7C63221/31A
Document #: 38-08028 Rev. *B
Page 15 of 50
execution begins from address 0x0000 after this t
START
delay period. This provides time for V
CC
to stabilize before the part
executes code. See Section 10.1 for more details.
1 = Disables the LVR circuit.
0 = Enables the LVR circuit.
Bit 2: Precision USB Clocking Enable
The Precision USB Clocking Enable only affects operation in internal oscillator mode.
In that mode, this bit must be set to
1 to cause the internal clock to automatically precisely tune to USB timing requirements (6 MHz ±1.5%)
. The frequency
may have a looser initial tolerance at power-up, but all USB transmissions from the chip will meet the USB specification.
1 = Enabled. The internal clock accuracy is
6 MHz ±1.5%
after USB traffic is received
.
0 = Disabled. The internal clock accuracy is 6 MHz ±5%.
Bit 1: Internal Clock Output Disable
The Internal Clock Output Disable is used to keep the internal clock from driving out to the XTALOUT pin. This bit has no effect
in the external oscillator mode.
1 = Disable internal clock output. XTALOUT pin will drive HIGH.
0 = Enable the internal clock output. The internal clock is driven out to the XTALOUT pin.
Bit 0: External Oscillator Enable
At power-up, the chip operates from the internal clock by default. Setting the External Oscillator Enable bit HIGH disables the
internal clock, and halts the part while the external resonator/crystal oscillator is started. Clearing this bit has no immediate
effect, although the state of this bit is used when waking out of suspend mode to select between internal and external clock.
In internal clock mode, XTALIN pin will be configured as an input with a weak pull-down and can be used as a GPIO input
(P2.1).
1 = Enable the external oscillator. The clock is switched to external clock mode, as described in Section 9.1.
0 = Enable the internal oscillator.
9.1
The internal oscillator provides an operating clock, factory set to a nominal frequency of 6 MHz. This clock requires no external
components. At power-up, the chip operates from the internal clock. In this mode, the internal clock is buffered and driven to the
XTALOUT pin by default, and the state of the XTALIN pin can be read at Port 2.1. While the internal clock is enabled, its output
can be disabled at the XTALOUT pin by setting the Internal Clock Output Disable bit of the Clock Configuration Register.
Setting the External Oscillator Enable bit of the Clock Configuration Register HIGH disables the internal clock, and halts the part
while the external resonator/crystal oscillator is started. The steps involved in switching from Internal to External Clock mode are
as follows:
1. At reset, chip begins operation using the internal clock.
2. Firmware sets Bit 0 of the Clock Configuration Register. For example,
mov A, 1h
; Set Bit 0 HIGH (External Oscillator Enable bit). Bit 7 cleared gives faster start-up
iowr F8h
; Write to Clock Configuration Register
3. Internal clocking is halted, the internal oscillator is disabled, and the external clock oscillator is enabled.
4. After the external clock becomes stable, chip clocks are re-enabled using the external clock signal. (Note that the time for the
external clock to become stable depends on the external resonating device; see next section.)
5. After an additional delay the CPU is released to run. This delay depends on the state of the Ext. Clock Resume Delay bit of
the Clock Configuration Register. The time is 128
μ
s if the bit is 0, or 4 ms if the bit is 1.
6. Once the chip has been set to external oscillator, it can only return to internal clock when waking from suspend mode. Clearing
bit 0 of the Clock Configuration Register will not re-enable internal clock mode until suspend mode is entered. See Section
11.0 for more details on suspend mode operation.
If the Internal Clock is enabled, the XTALIN pin can serve as a general-purpose input, and its state can be read at Port 2, Bit 1
(P2.1). Refer to
Figure 12-8
for the Port 2 Data Register. In this mode, there is a weak pull-down at the XTALIN pin. This input
cannot provide an interrupt source to the CPU.
Internal/External Oscillator Operation
9.2
The user can connect a low-cost ceramic resonator or an external oscillator to the XTALIN/XTALOUT pins to provide a precise
reference frequency for the chip clock, as shown in
Figure 9-1
. The external components required are a ceramic resonator or
crystal and any associated capacitors. To run from the external resonator, the External Oscillator Enable bit of the Clock Config-
uration Register must be set to 1, as explained in the previous section.
External Oscillator
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C64013C | Full-Speed USB (12-Mbps)(全速USB(12-Mbps)) |
| CY7C64113C | Full-Speed USB (12-Mbps)(全速USB(12-Mbps)) |
| CY7C64013 | Full-Speed USB (12 Mbps) Function(全速 USB (12 Mbps)性能) |
| CY7C64113 | Full-Speed USB (12 Mbps) Function(全速 USB (12 Mbps)性能) |
| CY7C64713 | EZ-USB FX1 USB Microcontroller Full-speed USB Peripheral Controller(EZ-USB FX1 USB微控制器，全速USB外設控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C63231A-PXC | 功能描述:8位微控制器 -MCU enCoRe RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C63231A-SC | 功能描述:IC MCU 3K USB LS PERIPH 18-SOIC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63231A-SXC | 功能描述:8位微控制器 -MCU enCoRe RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| CY7C63231A-SXCT | 功能描述:IC MCU 3K USB LS PERIPH 18-SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器 - 特定應用 系列:enCoRe™ 產品變化通告:Product Discontinuation 26/Aug/2009 標準包裝:250 系列:- 應用:網絡處理器 核心處理器:4Kc 程序存儲器類型:- 控制器系列:- RAM 容量:16K x 8 接口:以太網，UART，USB 輸入/輸出數:- 電源電壓:1.8V, 3.3V 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:208-LQFP 包裝:帶卷 (TR) 供應商設備封裝:PG-LQFP-208 其它名稱:SP000314382 |
| CY7C63310-PXC | 功能描述:USB 接口集成電路 USB 3K Flash 128 byte RAM COM RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。