- 您現在的位置：買賣IC網 > PDF目錄378513 > CY7C63231-PC (CYPRESS SEMICONDUCTOR CORP) enCoRe USB Low-speed USB Peripheral Controller PDF資料下載
參數資料
| 型號： | CY7C63231-PC |
| 廠商： | CYPRESS SEMICONDUCTOR CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | enCoRe USB Low-speed USB Peripheral Controller |
| 中文描述： | 8-BIT, OTPROM, RISC MICROCONTROLLER, PDIP18 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-18 |
| 文件頁數： | 18/49頁 |
| 文件大?。?/td> | 960K |
| 代理商： | CY7C63231-PC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
FOR
FOR
enCoRe
USB
CY7C63221/31A
Document #: 38-08028 Rev. *A
Page 18 of 49
11.1
When exiting suspend on a wake-up event, the device can be configured to run in either Internal or External Clock mode. The
mode is selected by the state of the External Oscillator Enable bit in the Clock Configuration Register (
Figure 9-2
). Using the
Internal Clock saves the external oscillator start-up time and keeps that oscillator off for additional power savings. The external
oscillator mode can be activated when desired, similar to operation at power-up.
The sequence of events for these modes is as follows:
Clocking Mode on Wake-up from Suspend
Wake in Internal Clock Mode:
1. Before entering suspend, clear bit 0 of the Clock Configuration Register. This selects Internal clock mode after suspend.
2. Enter suspend mode by setting the suspend bit of the Processor Status and Control Register.
3. After a wake-up event, the internal clock starts immediately (within 2
μ
s).
4. A time-out period of 8
μ
s passes, and then firmware execution begins.
5. At some later point, to activate External Clock mode, set bit 0 of the Clock Configuration Register. This halts the internal clocks
while the external clock becomes stable. After an additional time-out (128
μ
s or 4 ms, see Section 9.0), firmware execution
resumes.
Wake in External Clock Mode:
1. Before entering suspend, the external clock must be selected by setting bit 0 of the Clock Configuration Register. Make sure
this bit is still set when suspend mode is entered. This selects External clock mode after suspend.
2. Enter suspend mode by setting the suspend bit of the Processor Status and Control Register.
3. After a wake-up event, the external oscillator is started. The clock is monitored for stability (this takes approximately 50
–
100
μ
s with a ceramic resonator).
4. After an additional time-out period (128
μ
s or 4 ms, see Section 9.0), firmware execution resumes.
11.2
The wake-up timer runs whenever the wake-up interrupt is enabled, and is turned off whenever that interrupt is disabled.
Operation is independent of whether the device is in suspend mode or if the global interrupt bit is enabled. Only the Wake-up
Timer Interrupt Enable bit (
Figure 19-1
) controls the wake-up timer.
Once this timer is activated, it will give interrupts after its time-out period (see below). These interrupts continue periodically until
the interrupt is disabled. Whenever the interrupt is disabled, the wake-up timer is reset, so that a subsequent enable always
results in a full wake-up time.
The wake-up timer can be adjusted by the user through the Wake-up Timer Adjust bits in the Clock Configuration Register
(
Figure 9-2
). These bits clear on reset. In addition to allowing the user to select a range for the wake-up time, a firmware algorithm
can be used to tune out initial process and operating condition variations in this wake-up time. This can be done by timing the
wake-up interrupt time with the accurate 1.024-ms timer interrupt, and adjusting the Timer Adjust bits accordingly to approximate
the desired wake-up time.
Table 11-1. Wake-up Timer Adjust Settings
Wake-up Timer
Adjust Bits [2:0]
(Bits [6:4] in
Figure 9-2
)
000 (reset state)
001
010
011
100
101
110
111
See Section 24.0 for the value of t
WAKE
Wake-up Time
1 * t
WAKE
2 * t
WAKE
4 * t
WAKE
8 * t
WAKE
16 * t
WAKE
32 * t
WAKE
64 * t
WAKE
128 * t
WAKE
相關PDF資料 |
PDF描述 |
|---|---|
| CY7C63231A-SC | enCoRe USB Low-speed USB Peripheral Controller |
| CY7C63221A | enCoRe USB Low-speed USB Peripheral Controller |
| CY7C63221A-PC | enCoRe USB Low-speed USB Peripheral Controller |
| CY7C63221A-XC | TV 32C 32#20 SKT RECP |
| CY7C63231A | enCoRe USB Low-speed USB Peripheral Controller(enCoRe USB 低速USB外設控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CY7C63310-PXC | 功能描述:USB 接口集成電路 USB 3K Flash 128 byte RAM COM RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| CY7C63310-SXC | 功能描述:USB 接口集成電路 USB Peripheral Cntrl 3K/128 16-SOIC RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| CY7C63310-SXCES | 制造商:Cypress Semiconductor 功能描述: |
| CY7C634121C-PVXC | 制造商:Cypress Semiconductor 功能描述: |
| CY7C634121C-PXC | 制造商:Cypress Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。