參數資料
型號： CDB4364
廠商： Cirrus Logic Inc
文件頁數： 22/50頁
文件大?。?/td> 0K
描述： EVALUATION BOARD FOR CS4364
標準包裝： 1
DAC 的數量： 6
位數： 24
采樣率（每秒）： 192k
數據接口： 串行
DAC 型： 電壓
工作溫度： -40°C ~ 85°C
已供物品： 板
已用 IC / 零件： CS4364
相關產品： CS4364-CQZR-ND - IC DAC 103DB 24BIT 6CH 48-LQFP
598-1059-ND - IC DAC 103DB 24BIT 6CH 48-LQFP
DS619F1
29
CS4364
converted incorrectly by the Hardware Mode settings).
4.
Set the PDN bit to 0. This will initiate the power-up sequence, which lasts approximately 50 s.
4.13
Recommended Procedure for Switching Operational Modes
For systems where the absolute minimum in clicks and pops is required, it is recommended that the MUTE
bits are set prior to changing significant DAC functions (such as changing sample rates or clock sources).
The mute bits may then be released after clocks have settled and the proper modes have been set.
It is required to have the device held in reset if the minimum high/low time specs of MCLK can not be met
during clock source changes.
4.14
Control Port Interface
The control port is used to load all the internal register settings in order to operate in Software Mode (see
the “Parameter Definitions” on page 47). The operation of the control port may be completely asynchronous
with the audio sample rate. However, to avoid potential interference problems, the control port pins should
remain static if no operation is required.
The control port operates in one of two modes: IC or SPI.
4.14.1
MAP Auto Increment
The device has MAP (memory address pointer) auto increment capability enabled by the INCR bit (also
the MSB) of the MAP. If INCR is set to 0, MAP will stay constant for successive IC writes or reads and
SPI writes. If INCR is set to 1, MAP will auto increment after each byte is written, allowing block reads or
writes of successive registers.
4.14.2
IC Mode
In the IC Mode, data is clocked into and out of the bi-directional serial control data line, SDA, by the serial
control port clock, SCL (see Figure 22 for the clock to data relationship). There is no CS pin. Pin AD0 en-
ables the user to alter the chip address (001100[AD0][R/W]) and should be tied to VLC or GND as re-
quired, before powering up the device. If the device ever detects a high to low transition on the AD0/CS
pin after power-up, SPI Mode will be selected.
4.14.2.1 IC Write
To write to the device, follow the procedure below while adhering to the control port Switching Specifica-
tions in Section 2.
1.
Initiate a START condition to the IC bus followed by the address byte. The upper 6 bits must be
001100. The seventh bit must match the setting of the AD0 pin, and the eighth must be 0. The eighth
bit of the address byte is the R/W bit.
2.
Wait for an acknowledge (ACK) from the part, then write to the memory address pointer, MAP. This
byte points to the register to be written.
3.
Wait for an acknowledge (ACK) from the part, then write the desired data to the register pointed to by
the MAP.
4.
If the INCR bit (see Section 4.14.1) is set to 1, repeat the previous step until all the desired registers
are written, then initiate a STOP condition to the bus.
5.
If the INCR bit is set to 0 and further IC writes to other registers are desired, it is necessary to initiate
a repeated START condition and follow the procedure detailed from step 1. If no further writes to other
registers are desired, initiate a STOP condition to the bus.
相關PDF資料
PDF描述
RPP20-2412S/N CONV DC/DC 20W 18-36VIN 12VOUT
EBM11DRKF CONN EDGECARD 22POS DIP .156 SLD
EVAL-AD7985EBZ BOARD EVAL FOR AD7985
RPP20-2412D/N CONV DC/DC 20W 18-36VIN +/-12V
EBA22DTKH-S288 CONN EDGECARD 44POS .125 EXTEND
相關代理商/技術參數
參數描述
CDB4365 功能描述:音頻 IC 開發工具 Eval Bd 6-Ch DAC w/DSD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4382 制造商:Cirrus Logic 功能描述:Tools Development kit Kit Con
CDB4382A 功能描述:音頻 IC 開發工具 Eval Bd 114dB 192kHz 8-Ch DAC w/DSD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
CDB4383 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:114 dB, 192 kHz 8-Channel D/A Converter
CDB4384 功能描述:音頻 IC 開發工具 Eval Bd 8-Ch DAC w/DSD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*