- 您現在的位置：買賣IC網 > PDF目錄364678 > AN2897 Using the eTPU Angle Clock PDF資料下載
參數資料
| 型號： | AN2897 |
| 英文描述： | Using the eTPU Angle Clock |
| 中文描述： | 使用時鐘角的eTPU |
| 文件頁數： | 26/32頁 |
| 文件大?。?/td> | 587K |
| 代理商： | AN2897 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Using the eTPU Angle Clock, Rev. 0
eTPU Software Design
Freescale Semiconductor
26
The Angle Clock tick counter begins timing out when the tooth edge occurs. The calculation of a new value
for the Tick Rate Register will take some time to complete. While this is being done the old value is used
for the tick rate. At steady state this makes no difference, but when the wheel is accelerating, the first tick
is necessarily late. If the acceleration continues, all of the tick counts will be late and the Angle Clock will
have to go into High Rate mode to catch up.
It is possible to compensate for the accelerating wheel by adjusting the tick rate so that the next tooth is
counted a bit faster than a simple extrapolation. This adjustment can be added to the software design at the
engineer’s discretion.
This state is repeated for each new tooth detection until one of the following occurs:
1. The tooth count indicates that the gap is following next.
2. The tooth count indicates that the next tooth is the zero angle reference point.
3. The host requests service, for example to correct an error.
4. The following tooth is not detected within a specified time (stall).
4.2.9
Gapping
When the tooth count indicates that a new gap is expected, the system must verify that measured gap times
pass the designated test. If the gap is correctly placed, no host action is required. If the gap period is outside
the range of acceptability, the information should be passed up to the host by setting the status to
Error
.
The application can then analyze the error and execute a correction procedure.
NOTE
Once synchronized, the Angle Clock system can proceed indefinitely
without further host action, unless a signal anomaly occurs.
4.2.10 New Revolution
When the count of the teeth indicates that the last tooth in the cycle has been detected, and if the system
required a periodic angle count, the software must set the LAST bit so that the counter will reset at the next
detected tooth edge. Note that the counter reset will not occur on a tooth count inserted by MISSCNT
during the gap, although asserting the IPH when LAST is set will reset the TCR2.
In a 720 degree system, this point occurs every second revolution of the wheel. The phasing of the count
may be done automatically (for example, by using a cam detected signal to enable the reset logic) or
manually by having the host force
Full_Sync
based on the cam information.
4.2.11 Adjust Angle
Provision may be made in the Angle Clock software for the host to alter the angle indicated by the TCR2
counter. This action could be taken as a result of an independent determination that the counter fell out of
sync, perhaps as a result of detecting a spurious tooth. The system can use IPH or HOLD to advance or
retard the angle count by one tooth. Remember to correct the tooth count as well so that the next reset
occurs at the correct tooth position. When the Adjust Angle service request is processed, the function
相關PDF資料 |
PDF描述 |
|---|---|
| AN2904FHQ | AN2904FHQ - Sound input/output interface IC for digital still camera |
| AN2933 | Understanding the eTPU Channel Hardware |
| AN30210A | Analog IC |
| AN304 | Single Differential Amplifier |
| AN305 | Optoelectronic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN28F010109 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AN28F010-120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AN28F010-150 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AN28F256A-120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AN28F256A-150 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。