參數資料
型號： AN2897
英文描述： Using the eTPU Angle Clock
中文描述： 使用時鐘角的eTPU
文件頁數： 16/32頁
文件大?。?/td> 587K
代理商： AN2897
Using the eTPU Angle Clock, Rev. 0
System Design
Freescale Semiconductor
16
tooth edge signal, the Angle Clock design can only help detect the problem, and pass the information on
to the host for corrective action.
3.4.1
Error Prevention
The eTPU Angle Clock provides means to reject tooth edges detected outside of certain limits. This
rejection is done by an input pin hardware filter and by gating the tooth signal with a match registers in the
channel.
The TCRCLK input pin filter for the Angle Clock can use the input pin filters of the other eTPU channels,
or it can be programmed separately. These filters are designed to reject very short apparent pin transitions
such as might be caused by high frequency induced noise. In any case, this low pass filtering of the tooth
signal will introduce a time delay in the signal from the tooth. Since the filter time is generally in the order
of a few system clock times, the angle represented by this delay is very small even at high wheel speeds.
See the Reference Manual for details of the TCRCLK filter.
When Channel 0 is in one of the
m2_
modes, the MatchA register can be used as a blocking timer for input
signals. In this mode, the eTPU software can provide a blanking time after the detection of a tooth edge,
during which time a (presumably spurious) additional edge will be blocked. This feature is particularly
useful when an imperfect tooth detection circuit presents a chopped or hashed edge to the eTPU, which
often happens at low speed. If the frequency of the edge noise is lower than the pin filter rejection, a noise
pulse could be detected and counted as a tooth edge signal unless this blanking is used. The blanking match
can be programmed as an absolute time or calculated by the eTPU as a percentage of the previous period.
The choice depends on the expected characteristics of the edge noise.
If a noisy edge is possible, then a noisy return edge might also be detected as an active transition. If
blanking is used to prevent noise from being processed as a tooth edge, then the blanking must be applied
to both edges of the tooth signal.
If a tooth signal is completely lost to the eTPU channel by some means, the hardware alone cannot
distinguish the long period from any other deceleration. However, a second match can be setup in Channel
0 to request service if a transition has not occurred within a specified time.
3.4.2
Error Recovery
The tick counter in the eTPU Angle Clock ensures that there are exactly TICKS counts between physical
teeth. If the Angle Clock acquires an error less than one tooth count, the only possible reason is a software
error. Nevertheless, if even if the count acquires a small error, the count will rectify when the LAST tooth
is processed.
NOTE
The most common cause of a small TCR2 angle error is writing the initial
angle to the angle clock when synchronization occurs. When gap
synchronization is first verified, if the tick rate timer expires just as the
TCR2 value is incremented by the tick counter, the tick counts for
subsequent teeth count may fall short by one tick until the last tooth
re-synchronizes the tick counter.
相關PDF資料
PDF描述
AN2904FHQ AN2904FHQ - Sound input/output interface IC for digital still camera
AN2933 Understanding the eTPU Channel Hardware
AN30210A Analog IC
AN304 Single Differential Amplifier
AN305 Optoelectronic
相關代理商/技術參數
參數描述
AN28F010109 制造商:Rochester Electronics LLC 功能描述:- Bulk
AN28F010-120 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
AN28F010-150 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
AN28F256A-120 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
AN28F256A-150 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*