- 您現在的位置：買賣IC網 > PDF目錄364678 > AN2897 Using the eTPU Angle Clock PDF資料下載
參數資料
| 型號： | AN2897 |
| 英文描述： | Using the eTPU Angle Clock |
| 中文描述： | 使用時鐘角的eTPU |
| 文件頁數： | 18/32頁 |
| 文件大?。?/td> | 587K |
| 代理商： | AN2897 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Using the eTPU Angle Clock, Rev. 0
eTPU Software Design
Freescale Semiconductor
18
3.5
Tooth Circuit Failure
If the tooth circuit fails and the failure is detected by the host, the software may implement a limp home
strategy. The eTPU Angle Clock provides a method to disconnect the Angle Clock system from the
Channel 0 input so that spurious signals from the tooth circuit will not disrupt the limp home system. In
that event, the host may configure the eTPU such that Channel 0 continues to monitor the tooth circuit for
diagnostic purpose. See the Reference Manual for details.
4
eTPU Software Design
The software shown below is taken from an Automotive Reference Design which demonstrates the
operation and application of the eTPU Angle Clock in a practical automotive engine control system. Code
that is directly copied is displayed in
Courier New
font. The Reference Design is free to customers
and can be obtained from Byte Craft, Ash Ware, or your Freescale representative.
4.1
Host Setup
The host must setup the registers and parameters in the eTPU to enable the Angle Clock. In addition to the
setup required for any eTPU operation, use of the Angle Clock requires the following steps.
a) The Angle Mode bit in the ETPUTBCR must be set.
b) The TCRCLK Filter Mode must be setup.
c) Initial Channel 0 parameters must be written.
d) Channel 0 must be initialized.
e) The TCR2 Clock Source in the ETPUTBCR must be set for rising or falling edges to match
the IPAC setting for the tooth in Channel 0.
The last step may be delayed until Channel 0 has confirmed synchronization.
相關PDF資料 |
PDF描述 |
|---|---|
| AN2904FHQ | AN2904FHQ - Sound input/output interface IC for digital still camera |
| AN2933 | Understanding the eTPU Channel Hardware |
| AN30210A | Analog IC |
| AN304 | Single Differential Amplifier |
| AN305 | Optoelectronic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN28F010109 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| AN28F010-120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AN28F010-150 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AN28F256A-120 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| AN28F256A-150 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。