- 您現在的位置：買賣IC網 > PDF目錄364674 > AMC6821SDBQR Analog Monitor and Control Circuit PDF資料下載
參數資料
| 型號： | AMC6821SDBQR |
| 英文描述： | Analog Monitor and Control Circuit |
| 中文描述： | 模擬監(jiān)視和控制電路 |
| 文件頁數： | 34/47頁 |
| 文件大?。?/td> | 547K |
| 代理商： | AMC6821SDBQR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
www.ti.com
P
DEVICE STATUS REGISTERS
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
Reading the status registers clears the appropriate status bit. Status register bits are sticky (except the RTF bit).
Whenever a status bit is set, indicating an out-of-limit condition, it remains set until the event that caused it is
resolved and the status register is read. The status bit can only be cleared by reading the status register after
the event is resolved. All bits are cleared when reading the register, and all bits are reasserted if the out-of limit
condition still exists on the next monitoring cycle, unless otherwise noted.
Status Register 1 (Address 0x02, Value After Power-On or Reset = 0x00)
BIT
NAME
R/W
DEFAULT
DESCRIPTION
LTL = 1 when the local temperature is less than or equal to the value of the
Local-Low-Temp-Limit register. Otherwise, LTL = 0. If the local temperature is still
outside the local temperature low limit, this bit reasserts on the next monitoring cycle.
LTH = 1 when the local temperature is greater than or equal to the value of the
Local-High-Temp-Limit register. Otherwise, LTH = 0. If the local temperature is still
outside the local temperature high limit, this bit reasserts on the next monitoring cycle.
Remote sensor-failure interrupt. RTF = 1 when the remote temperature sensor fails
(short- or open-circuit). RTF = 0 when the remote sensor is in normal condition. When
RTF = 1, the OVR.RTF pin is asserted and the remote temperature data register is set
to 0x800 (–128
°
C).
RTF = 1 also generates an interrupt through the SMBALERT pin if an interrupt is
enabled (RTFIE = 1). Once RTF is set ('1'), it always remains ('1') until power-on reset
or software reset occurs, whether or not the failure condition continues. Reading the
status register does not clear the RTF bit.
Remote temperature over the remote THERM limit flag. R-THERM = 1 when the
temperature is greater than the value of the Remote-THERM-Limit register. Otherwise,
R-THERM = 0. When R-THERM = 1, the THERM pin goes low. It also generates a
THERM interrupt if THERMOVIE = 1. This bit is cleared on a read of
Status Register 1
.
Once cleared, this bit is not reasserted until the remote temperature falls 5
°
C below this
THERM limit, even if the THERM condition persists. Refer to the
THERM Pin and
External Hardware Control
section.
RTL = 1 when the remote temperature is less than or equal to the value of the
Remote-Low-Temp-Limit register. Otherwise, RTL = 0. If the remote temperature is still
beyond the remote temperature low limit, this bit reasserts on the next monitoring cycle.
RTH = 1 when the remote temperature is greater than or equal to the value of
Remote-High-Temp-Limit register. Otherwise, RTH = 0. If the remote temperature is still
beyond the remote temperature high limit, this bit reasserts on the next monitoring cycle.
Fan-slow flag. FANS = 1 if the TACH data are greater than or equal to the value of the
TACH-Low-Limit register. This bit indicates if the fan becomes stuck or goes under the
minimum speed. FANS = 0 if the TACH data are smaller than the TACH low limit. This
bit is cleared ('0') only after reading this register, and reasserts '1' in the next monitoring
if a fan-slow is detected. After spin-up, FANS is set ('1') even if the TACH data are less
than the TACH low limit until the register is read. FANS = 1 generates a FAN-ORN
interrupt through the SMBALERT pin if FANORN is enabled (FANIE = 1). Five
consecutive fan-slow returns results in a
FAN FAILURE
status; which asserts the
FAN-FAULT pin low. This interrupt is a non-maskable interrupt (see the
FAN-FAULT
PIN
section for details). Note that a no-FANS (fan-slow) detection is made during
spin-up.
RPM-ALARM = 1 when the TACH data are less than or equal to the value of the
TACH-High-Limit register. This means the RPM is over the maximum limit defined by
the TACH high limit. Otherwise, RPM-ALARM = 0. This bit is cleared when reading this
register. Once cleared, this bit is not reasserted on the next monitoring cycle even if the
condition still persists. This bit may be reasserted only if the RPM drops below the
allowed maximum speed. RPM-ALARM = 1 generates a FANORN (fan-out-of-range)
interrupt through the SMBALERT pin if FANORN is enabled (FANIE = 1), but does not
cause an interrupt through the FAN-FAULT pin.
7
LTL
R
0
6
LTH
R
0
5
RTF
R
0
4
R-THERM
R
0
3
RTL
R
0
2
RTH
R
0
1
FANS
R
0
0
RPM-ALARM
R
0
34
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| AMD-8111 | AMD-8111? HyperTransport? I/O Hub Revision Guide |
| AMD-8131 | AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet |
| AMD-8151 | AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet |
| AMD64 | AMD64 Architecture Programmer＇s Manual Volume 1: Application Programming |
| AMDATHLON | AMD Athlon - AMD Athlon Processor Model 4 Revision Guide |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMC6821SDBQRG4 | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC6821SQDBQRQ1 | 功能描述:馬達/運動/點火控制器和驅動器 Auto Cat Temp Mon and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC682J50ACK | 制造商:Nissei Electric 功能描述:CAPACITOR, METALLIZED FILM, POLYESTER, 50 V, 0.0068 uF, THROUGH HOLE MOUNT |
| AMC69G-V30 | 制造商:Panasonic Industrial Company 功能描述:KNOB |
| AMC69R-1L0 | 制造商:Panasonic Industrial Company 功能描述:HOLDER |
發(fā)布緊急采購，3分鐘左右您將得到回復。