- 您現在的位置：買賣IC網 > PDF目錄364674 > AMC6821SDBQR Analog Monitor and Control Circuit PDF資料下載
參數資料
| 型號： | AMC6821SDBQR |
| 英文描述： | Analog Monitor and Control Circuit |
| 中文描述： | 模擬監視和控制電路 |
| 文件頁數： | 21/47頁 |
| 文件大?。?/td> | 547K |
| 代理商： | AMC6821SDBQR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
www.ti.com
P
Fan Spin-Up
Normal
Control
DCY
100%
0
T
/3
SPIN-UP
T
SPIN-UP
33.3%
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
The PWM duty cycle controls the cooling fan speed. To spin-up a fan from a stop or under-speed status, the
spin-up process is applied to overcome the fan inertia. During the first third of spin-up, the duty cycle of the
PWM gradually increases from 33.3% to 100%, and then maintains at 100% through the rest of the process. At
the end of the spin-up process, the duty cycle is adjusted to 33.3%. After starting, the fan speed is controlled
normally. The spin-up process is shown in
Figure 15
. The bits [STIME2:STIME0] (bits 2:0 of 0x20) define the
spin-up time, from 0.2 seconds to 8 seconds, as shown in
Table 6
. Fan speed is monitored immediately after the
spin-up process.
Spin-up is disabled by setting the FSPD bit of the
Fan Characteristics Register
to '1'. If disabled, the spin-up
process is not applied when the fan stops or an RPM is detected below the minimum speed. The TACH low limit
register defines the minimum speed.
Note that no FANS (fan-slow) detections are performed during spin-up. This bit is cleared ('0') only after reading
it, and reasserts '1' in the next monitoring if a fan-slow condition is detected. After spin-up, FANS is set ('1') even
if the TACH data are less than the TACH low limit until the flag is read.
Figure 15. Spin-Up Process
Table 6. Spin-Up Time
STIME2
0
0
0
0
1
1
1
1
STIME1
0
0
1
1
0
0
1
1
STIME0
0
1
0
1
0
1
0
1
SPIN-UP TIME (seconds)
0.2
0.4
0.6
0.8
1
2
4
8
21
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| AMD-8111 | AMD-8111? HyperTransport? I/O Hub Revision Guide |
| AMD-8131 | AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet |
| AMD-8151 | AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet |
| AMD64 | AMD64 Architecture Programmer＇s Manual Volume 1: Application Programming |
| AMDATHLON | AMD Athlon - AMD Athlon Processor Model 4 Revision Guide |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMC6821SDBQRG4 | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC6821SQDBQRQ1 | 功能描述:馬達/運動/點火控制器和驅動器 Auto Cat Temp Mon and Fan Control RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC682J50ACK | 制造商:Nissei Electric 功能描述:CAPACITOR, METALLIZED FILM, POLYESTER, 50 V, 0.0068 uF, THROUGH HOLE MOUNT |
| AMC69G-V30 | 制造商:Panasonic Industrial Company 功能描述:KNOB |
| AMC69R-1L0 | 制造商:Panasonic Industrial Company 功能描述:HOLDER |
發布緊急采購，3分鐘左右您將得到回復。