參數資料
型號： AMC6821
英文描述： Analog Monitor and Control Circuit
中文描述： 模擬監視和控制電路
文件頁數： 34/47頁
文件大小： 547K
代理商： AMC6821
www.ti.com
P
DEVICE STATUS REGISTERS
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
Reading the status registers clears the appropriate status bit. Status register bits are sticky (except the RTF bit).
Whenever a status bit is set, indicating an out-of-limit condition, it remains set until the event that caused it is
resolved and the status register is read. The status bit can only be cleared by reading the status register after
the event is resolved. All bits are cleared when reading the register, and all bits are reasserted if the out-of limit
condition still exists on the next monitoring cycle, unless otherwise noted.
Status Register 1 (Address 0x02, Value After Power-On or Reset = 0x00)
BIT
NAME
R/W
DEFAULT
DESCRIPTION
LTL = 1 when the local temperature is less than or equal to the value of the
Local-Low-Temp-Limit register. Otherwise, LTL = 0. If the local temperature is still
outside the local temperature low limit, this bit reasserts on the next monitoring cycle.
LTH = 1 when the local temperature is greater than or equal to the value of the
Local-High-Temp-Limit register. Otherwise, LTH = 0. If the local temperature is still
outside the local temperature high limit, this bit reasserts on the next monitoring cycle.
Remote sensor-failure interrupt. RTF = 1 when the remote temperature sensor fails
(short- or open-circuit). RTF = 0 when the remote sensor is in normal condition. When
RTF = 1, the OVR.RTF pin is asserted and the remote temperature data register is set
to 0x800 (–128
°
C).
RTF = 1 also generates an interrupt through the SMBALERT pin if an interrupt is
enabled (RTFIE = 1). Once RTF is set ('1'), it always remains ('1') until power-on reset
or software reset occurs, whether or not the failure condition continues. Reading the
status register does not clear the RTF bit.
Remote temperature over the remote THERM limit flag. R-THERM = 1 when the
temperature is greater than the value of the Remote-THERM-Limit register. Otherwise,
R-THERM = 0. When R-THERM = 1, the THERM pin goes low. It also generates a
THERM interrupt if THERMOVIE = 1. This bit is cleared on a read of
Status Register 1
.
Once cleared, this bit is not reasserted until the remote temperature falls 5
°
C below this
THERM limit, even if the THERM condition persists. Refer to the
THERM Pin and
External Hardware Control
section.
RTL = 1 when the remote temperature is less than or equal to the value of the
Remote-Low-Temp-Limit register. Otherwise, RTL = 0. If the remote temperature is still
beyond the remote temperature low limit, this bit reasserts on the next monitoring cycle.
RTH = 1 when the remote temperature is greater than or equal to the value of
Remote-High-Temp-Limit register. Otherwise, RTH = 0. If the remote temperature is still
beyond the remote temperature high limit, this bit reasserts on the next monitoring cycle.
Fan-slow flag. FANS = 1 if the TACH data are greater than or equal to the value of the
TACH-Low-Limit register. This bit indicates if the fan becomes stuck or goes under the
minimum speed. FANS = 0 if the TACH data are smaller than the TACH low limit. This
bit is cleared ('0') only after reading this register, and reasserts '1' in the next monitoring
if a fan-slow is detected. After spin-up, FANS is set ('1') even if the TACH data are less
than the TACH low limit until the register is read. FANS = 1 generates a FAN-ORN
interrupt through the SMBALERT pin if FANORN is enabled (FANIE = 1). Five
consecutive fan-slow returns results in a
FAN FAILURE
status; which asserts the
FAN-FAULT pin low. This interrupt is a non-maskable interrupt (see the
FAN-FAULT
PIN
section for details). Note that a no-FANS (fan-slow) detection is made during
spin-up.
RPM-ALARM = 1 when the TACH data are less than or equal to the value of the
TACH-High-Limit register. This means the RPM is over the maximum limit defined by
the TACH high limit. Otherwise, RPM-ALARM = 0. This bit is cleared when reading this
register. Once cleared, this bit is not reasserted on the next monitoring cycle even if the
condition still persists. This bit may be reasserted only if the RPM drops below the
allowed maximum speed. RPM-ALARM = 1 generates a FANORN (fan-out-of-range)
interrupt through the SMBALERT pin if FANORN is enabled (FANIE = 1), but does not
cause an interrupt through the FAN-FAULT pin.
7
LTL
R
0
6
LTH
R
0
5
RTF
R
0
4
R-THERM
R
0
3
RTL
R
0
2
RTH
R
0
1
FANS
R
0
0
RPM-ALARM
R
0
34
Submit Documentation Feedback
相關PDF資料
PDF描述
AMC6821SDBQ Analog Monitor and Control Circuit
AMC6821SDBQR Analog Monitor and Control Circuit
AMD-8111 AMD-8111? HyperTransport? I/O Hub Revision Guide
AMD-8131 AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet
AMD-8151 AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet
相關代理商/技術參數
參數描述
AMC6821EVM 功能描述:溫度傳感器開發工具 ANA MONITOR RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
AMC6821EVM-PDK 功能描述:溫度傳感器開發工具 THERMAL MGMT RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
AMC6821-Q1 制造商:TI 制造商全稱:Texas Instruments 功能描述:INTELLIGENT TEMPERATURE MONITOR AND PWM FAN CONTROLLER
AMC6821SDBQ 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SDBQG4 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*