- 您現在的位置：買賣IC網 > PDF目錄364674 > AMC6821 Analog Monitor and Control Circuit PDF資料下載
參數資料
| 型號： | AMC6821 |
| 英文描述： | Analog Monitor and Control Circuit |
| 中文描述： | 模擬監視和控制電路 |
| 文件頁數： | 20/47頁 |
| 文件大?。?/td> | 547K |
| 代理商： | AMC6821 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
www.ti.com
P
Status Register Read
THERM Limit
Temperature
THERM
INT
SMBALERT
via
INT
SMBALERT
via
5
°
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
When the THERM limit is exceeded, the corresponding status flag bit (R-THERM or L-THERM of
Status
Register 1
or
Status Register 2
) is set to '1', and the THERM interrupt through the SMBALERT pin is generated
if it is enabled (THERMOVIE of bit
Configuration Register 1
is set to '1'). This interrupt forces the SMBALERT
pin low. Reading the status registers clears the flag bit (R-THERM and L-THERM). Clearing the flag bit makes
the SMBALERT pin go back to high, but does not negate the THERM pin. It remains low until the temperature
falls 5°C below the exceeded THERM limit. After this bit is cleared, the active flag bit (R-THERM for remote
temperature or L-THERM for local temperature) and the THERM interrupt are not re-armed until the temperature
falls 5
°
C below the exceeded THERM limit. This procedure is shown in
Figure 14
.
Figure 14. Operation of the THERM Interrupt and the THERM Pin
When working as an output, the status of the THERM pin affects the RPM fan. If the THERM-FAN-EN bit is set
('1'), the fan goes to full-speed (that is, the duty cycle is 100%) when the THERM pin goes low. However, when
THERM-FAN-EN = 0, the status of the THERM pin does not affect the fan speed.
THERM Pin As An Input
When this pin works as input, it is the input of the external hardware control signal; the THERM-IN bit of
Status
Register 2
reflects the input. When the THERM pin is pulled low as an input, THERM-IN is set ('1') and the fan is
driven at full speed (that is, the duty cycle is 100%), no matter what THERM-FAN-EN is. The THERM-FAN-EN
bit has no effect when the THERM pin works as an input.
20
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| AMC6821SDBQ | Analog Monitor and Control Circuit |
| AMC6821SDBQR | Analog Monitor and Control Circuit |
| AMD-8111 | AMD-8111? HyperTransport? I/O Hub Revision Guide |
| AMD-8131 | AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet |
| AMD-8151 | AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMC6821EVM | 功能描述:溫度傳感器開發工具 ANA MONITOR RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| AMC6821EVM-PDK | 功能描述:溫度傳感器開發工具 THERMAL MGMT RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| AMC6821-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:INTELLIGENT TEMPERATURE MONITOR AND PWM FAN CONTROLLER |
| AMC6821SDBQ | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC6821SDBQG4 | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。