參數資料
型號： AMC6821
英文描述： Analog Monitor and Control Circuit
中文描述： 模擬監視和控制電路
文件頁數： 31/47頁
文件大?。?/td> 547K
代理商： AMC6821
www.ti.com
P
REGISTER DESCRIPTION
In this section, all interrupts are the interrupt signal through the SMBALERT pin, unless otherwise noted.
DEVICE CONFIGURATION REGISTERS
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
Configuration Register 1 (Address 0x00, Value After Power-On Reset = 0xD4)
BIT
NAME
R/W
DEFAULT
DESCRIPTION
THERM interrupt enable. When this bit is set, the THERM interrupt is enabled.
L-THERM = 1 or R-THERM = 1 causes an interrupt. When this bit is cleared ('0'), the
THERM interrupt is disabled. When disabled, L-THERM = 1 or R-THERM = 1 does not
assert the SMBALERT pin, but forces the THERM pin low. Power-on default = 1.
Fan driver control bit 1. Power-on default = 1. Refer to
Table 8
.
Fan driver control bit 0. Power-on default = 0. Refer to
Table 8
.
Setting this pin to '1' enables the FAN-FAULT pin. Clearing this pin ('0') disables the
FAN-FAULT pin (always in Hi-Z). Power-on default = 1.
PWM invert bit. When PWMINV = 0 (default), the PWM-Out pin goes low for 100% duty
cycle (suitable for driving the fan using a PMOS device). Setting PWMINV to '1' makes
the PWM-Out pin go high (with an external pull-up resistor) for 100% duty cycle
(suitable for driving the fan using a NMOS device). Power-on default = 0.
Fan RPM interrupt enable bit. Power-on default = 1. When FANIE = 1, the FAN-RPM
interrupt is enabled. FANS = 1 or RPM-ALARM = 1 generates a FANORN interrupt,
making the SMBALERT pin go low. When FANIE = 0, a FAN-RPM interrupt is disabled.
FANORN = 1 does not generate an interrupt.
Setting this bit to '1' enables the interrupt from the SMBALERT pin. Clearing this bit ('0')
disables the interrupt. Power-on default = 0.
'1' enables monitoring (temperatures and RPM) and PWM outputs. '0' disables
monitoring and PWM output. All registers should be programmed by BIOS before setting
this bit to 1. Power-on default = 0.
7
THERMOVIE
R/W
1
6
5
FDRC1
FDRC0
R/W
R/W
1
0
4
FAN-Fault-EN
R/W
1
3
PWMINV
R/W
0
2
FANIE
R/W
1
1
INT-EN
R/W
0
0
START
R/W
0
Table 8. Fan Driver Control Bits
FDRC1
FDRC0
FUNCTION
Maximum fast speed calculated by the local temperature-fan control and the remote
temperature-fan control.
Auto remote-temperature-fan control. The PWM duty cycle is controlled by the remote
temperature. Power-on default mode.
Software DCY control. Host writes DCY register to set the PWM duty cycle.
Software RPM control. Host writes the TACH setting register with the value corresponding
to the desired RPM. The device measures the actual RPM and adjusts the PWM duty cycle
to maintain the fan speed to the desired value.
1
1
1
0
0
0
0
1
31
Submit Documentation Feedback
相關PDF資料
PDF描述
AMC6821SDBQ Analog Monitor and Control Circuit
AMC6821SDBQR Analog Monitor and Control Circuit
AMD-8111 AMD-8111? HyperTransport? I/O Hub Revision Guide
AMD-8131 AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet
AMD-8151 AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet
相關代理商/技術參數
參數描述
AMC6821EVM 功能描述:溫度傳感器開發工具 ANA MONITOR RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
AMC6821EVM-PDK 功能描述:溫度傳感器開發工具 THERMAL MGMT RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流:
AMC6821-Q1 制造商:TI 制造商全稱:Texas Instruments 功能描述:INTELLIGENT TEMPERATURE MONITOR AND PWM FAN CONTROLLER
AMC6821SDBQ 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
AMC6821SDBQG4 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*