- 您現在的位置：買賣IC網 > PDF目錄364674 > AMC6821 Analog Monitor and Control Circuit PDF資料下載
參數資料
| 型號： | AMC6821 |
| 英文描述： | Analog Monitor and Control Circuit |
| 中文描述： | 模擬監視和控制電路 |
| 文件頁數： | 32/47頁 |
| 文件大?。?/td> | 547K |
| 代理商： | AMC6821 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
www.ti.com
P
AMC6821
SBAS386A–MAY 2006–REVISED MAY 2006
Configuration Register 2 (Address 0x01, Value After Power-On Reset = 0x3D)
BIT
NAME
R/W
DEFAULT
DESCRIPTION
Reset bits. RST = 1 resets the device. Self-clears after reset. Always read '0'. Power-on
default = 0.
LPSV enable bit. Power-on default = 0. When LPSVIE = 1, the LPSV interrupt is
enabled and an interrupt is generated when LPSV = 1. When LPSVIE = 0, LPSV is
disabled and LPSV = 1 does not cause an interrupt.
Remote temperature interrupt enable bit. When RTIE = 1, the remote temperature
interrupt is enabled and RTO = 1 causes an interrupt. When RTIE = 0, the remote
temperature interrupt is disabled and RTO = 1 does not generate an interrupt. Power-on
default = 1, except when a remote sensor failure is detected at power-on.
Local temperature interrupt enable bit. Power-on default = 1. When LTIE = 1, the local
temperature interrupt is enabled and LTO = 1 causes an interrupt. When LTIE = 0, the
local temperature interrupt is disabled and LTO = 1 does not generate an interrupt.
Remote sensor failure interrupt enable bit. Power-on default = 1. When RTFIE = 1, the
remote sensor failure interrupt is enabled and RTF = 1 causes an interrupt through the
SMBALERT pin. When RTFIE = 0, the remote sensor failure interrupt is disabled and
RTF = 1 does not generate an interrupt.
Setting this bit to '1' enables the TACH input. Clearing ('0') disables the TACH input.
Power-on default = 1.
When the TACH-MODE bit is cleared ('0'), the PWM-Out pin is forced
ON
during RPM
measurement, and internal correction circuitry is enabled to correct the error caused by
this extra duty cycle. Making TACH-MODE = 0 for the fans that are switched ON/OFF
directly by the PWM requires
PWM ON
to provide TACH pulses. In the software RPM
mode, the PWM-Out is forced to 30% duty cycle if the calculated duty cycle is less than
30% when TACH-MODE = 0. In all other modes the PWM-Out is forced to 0% if the
calculated duty cycle is less than 7%. When the TACH mode is set ('1'), the internal
correction circuit is disabled and PWM-Out is not forced
ON
. Instead, the PWM-Out pin
is completely controlled by the value of the DCY register, just as in normal operation.
Setting the TACH-MODE bit ('1') when the fans can provide TACH pulses output
regardless the status of the PWM-Out pin. The TACH mode must be '1' for any fan
which is powered directly by dc power, such as a four-wire fan. Power-on default = 0.
(See the
TACH-DATA Register
section for details.)
Setting this bit to '1' enables the PWM-Out pin. Clearing ('0') disables the PWM-Out pin
(H-Z). Power-on default = 1.
7
RST
R/W
0
6
PSVIE
R/W
0
5
RTOIE
R/W
1
4
LTOIE
R/W
1
3
RTFIE
R/W
1
2
TACH-EN
R/W
1
1
TACH-MODE
R/W
0
0
PWM-EN
R/W
1
Configuration Register 3 (Address 0x3F, Value After Power-On Reset = 0x82)
BIT
NAME
R/W
DEFAULT
DESCRIPTION
Setting this bit to 1 enables the fan to run at full-speed when the THERM pin
(as an output) is asserted low. This configuration allows the system to be run in
performance mode. Clearing this bit to '0' disables the fan from running at
full-speed whenever the THERM pin (as an output) is asserted low. This
configuration allows the system to run in silent mode. Note that this bit has no
effect whenever THERM is pulled low as an input. The fan always runs at full
speed when the THERM pin is pulled low as an input. Power-on default = 1.
Read-back '0'.
Read-back '0'.
Read-back '0'.
0, bit 3 (MSB) of 4-bit revision number.
0, bit 2 of revision number.
0, bit 1 of revision number.
0, bit 0 (LSB) of revision number.
7
THERM-FAN-EN
R/W
1
6
5
4
3
2
1
0
Reserved
Reserved
Reserved
R
R
R
R
R
R
R
0
0
0
0
0
1
0
Part Revision Number
Part Revision Number
Part Revision Number
Part Revision Number
32
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| AMC6821SDBQ | Analog Monitor and Control Circuit |
| AMC6821SDBQR | Analog Monitor and Control Circuit |
| AMD-8111 | AMD-8111? HyperTransport? I/O Hub Revision Guide |
| AMD-8131 | AMD-8131 - AMD-8131 HyperTransport PCI-X Tunnel Data Sheet |
| AMD-8151 | AMD-8151 - Preliminary AMD-8151 HyperTransport AGP3.0 Graphics Tunnel Data Sheet |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMC6821EVM | 功能描述:溫度傳感器開發工具 ANA MONITOR RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| AMC6821EVM-PDK | 功能描述:溫度傳感器開發工具 THERMAL MGMT RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| AMC6821-Q1 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:INTELLIGENT TEMPERATURE MONITOR AND PWM FAN CONTROLLER |
| AMC6821SDBQ | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| AMC6821SDBQG4 | 功能描述:馬達/運動/點火控制器和驅動器 Temp Monitoring and Fan Ctrl RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。