- 您現在的位置：買賣IC網 > PDF目錄366550 > AM79C972BKCW (ADVANCED MICRO DEVICES INC) PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support PDF資料下載
參數資料
| 型號： | AM79C972BKCW |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| 中文描述： | 5 CHANNEL(S), 100M bps, LOCAL AREA NETWORK CONTROLLER, PQFP16 |
| 封裝： | PLASTIC, QFP-160 |
| 文件頁數： | 51/130頁 |
| 文件大?。?/td> | 1580K |
| 代理商： | AM79C972BKCW |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁
Am79C972
51
to CSR15, and then setting the START bit in CSR0.
Note that this form of restart will not perform the same
in the Am79C972 controller as in the C-LANCE device.
In particular, upon restart, the Am79C972 controller re-
loads the transmit and receive descriptor pointers with
their respective base addresses. This means that the
software must clear the descriptor OWN bits and reset
its descriptor ring pointers before restarting the
Am79C972 controller. The reload of descriptor base
addresses is performed in the C-LANCE device only
after initialization, so that a restart of the C-LANCE
without initialization leaves the C-LANCE pointing at
the same descriptor locations as before the restart.
Suspend
The Am79C972 controller offers two suspend modes
that allow easy updating of the CSR registers without
going through a full re-initialization of the device. The
suspend modes also allow stopping the device with or-
derly termination of all network activity.
The host requests the Am79C972 controller to enter
the suspend mode by setting SPND (CSR5, bit 0) to 1.
The host must poll SPND until it reads back 1 to deter-
mine that the Am79C972 controller has entered the
suspend mode. When the host sets SPND to 1, the pro-
cedure taken by the Am79C972 controller to enter the
suspend mode depends on the setting of the fast sus-
pend enable bit (FASTSPND, CSR7, bit 15).
When a fast suspend is requested (FASTSPND is set
to 1), the Am79C972 controller performs a quick entry
into the suspend mode. At the time the SPND bit is set,
the Am79C972 controller will continue the DMA pro-
cess of any transmit and/or receive packets that have
already begun DMA activity until the network activity
has been completed. In addition, any transmit packet
that had started transmission will be fully transmitted
and any receive packet that had begun reception will be
fully received. However, no additional packets will be
transmitted or received and no additional transmit or re-
ceive DMA activity will begin after network activity has
ceased. Hence, the Am79C972 controller may enter
the suspend mode with transmit and/or receive packets
still in the FIFOs or the SRAM. This offers a worst case
suspend time of a maximum length packet over the
possibility of completely emptying the SRAM. Care
must be exercised in this mode, because the entire
memory subsystem of the Am79C972 controller is sus-
pended. Any changes to either the descriptor rings or
the SRAM can cause the Am79C972 controller to start
up in an unknown condition and could cause data cor-
ruption.
When FASTSPNDE is 0 and the SPND bit is set, the
Am79C972 controller may take longer before entering
the suspend mode. At the time the SPND bit is set, the
Am79C972 controller will complete the DMA process of
a transmit packet if it had already begun and the
Am79C972 controller will completely receive a receive
packet if it had already begun. The Am79C972 control-
ler will not receive any new packets after the comple-
tion of the current reception. Additionally, all transmit
packets stored in the transmit FIFOs and the transmit
buffer area in the SRAM (if one is present) will be trans-
mitted, and all receive packets stored in the receive
FIFOs and the receive buffer area in the SRAM (if se-
lected) will be transferred into system memory. Since
the FIFO and the SRAM contents are flushed, it may
take much longer before the Am79C972 controller en-
ters the suspend mode. The amount of time that it
takes depends on many factors including the size of the
SRAM, bus latency, and network traffic level.
Upon completion of the described operations, the
Am79C972 controller sets the read-version of SPND to
1 and enters the suspend mode. In suspend mode, all
of the CSR and BCR registers are accessible. As long
as the Am79C972 controller is not reset while in sus-
pend mode (by H_RESET, S_RESET, or by setting the
STOP bit), no re-initialization of the device is required
after the device comes out of suspend mode. When
SPND is set to 0, the Am79C972 controller will leave
the suspend mode and will continue at the transmit and
receive descriptor ring locations where it was when it
entered the suspend mode.
See the section on
Magic Packet
technology for de-
tails on how that affects suspension of the Am79C972
controller.
Buffer Management
Buffer management is accomplished through message
descriptor entries organized as ring structures in mem-
ory. There are two descriptor rings, one for transmit and
one for receive. Each descriptor describes a single
buffer. A frame may occupy one or more buffers. If mul-
tiple buffers are used, this is referred to as buffer chain-
ing.
Descriptor Rings
Each descriptor ring must occupy a contiguous area of
memory. During initialization, the user-defined base
address for the transmit and receive descriptor rings,
as well as the number of entries contained in the de-
scriptor rings are set up. The programming of the soft-
ware style (SWSTYLE, BCR20, bits 7-0) affects the
way the descriptor rings and their entries are arranged.
When SWSTYLE is at its default value of 0, the de-
scriptor rings are backwards compatible with the
Am79C90 C-LANCE and the Am79C96x PCnet-ISA
family. The descriptor ring base addresses must be
aligned to an 8-byte boundary and a maximum of 128
ring entries is allowed when the ring length is set
through the TLEN and RLEN fields of the initialization
block. Each ring entry contains a subset of the three
32-bit transmit or receive message descriptors (TMD,
RMD) that are organized as four 16-bit structures
相關PDF資料 |
PDF描述 |
|---|---|
| AM79C972BKIW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972BVCW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972 | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972BVIW | PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C974 | PCnetTM-SCSI Combination Ethernet and SCSI Controller for PCI Systems |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AM79C972BKD/W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C972BKD\\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C972BKD\W | 制造商:Advanced Micro Devices 功能描述: |
| AM79C972BKIW | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:PCnet⑩-FAST+ Enhanced 10/100 Mbps PCI Ethernet Controller with OnNow Support |
| AM79C972BVC | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。