- 您現在的位置：買賣IC網 > PDF目錄374046 > ADV7180BSTZ (ANALOG DEVICES INC) 10-Bit, 4 x Oversampling SDTV Video Decoder PDF資料下載
參數資料
| 型號： | ADV7180BSTZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 顏色信號轉換 |
| 英文描述： | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| 中文描述： | COLOR SIGNAL DECODER, PQFP64 |
| 封裝： | 10 X 10 MM, ROHS COMPLIANT, MS-026BCD, LQFP-64 |
| 文件頁數： | 53/112頁 |
| 文件大?。?/td> | 1320K |
| 代理商： | ADV7180BSTZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
ADV7180
VDP_TTXT_TYPE_MAN_ENABLE, Enable Manual
Selection of Teletext Type, Address 0x60 [2], User Sub Map
0
(default)—Manual programming of the teletext type is
disabled.
1—Manual programming of the teletext type is enabled.
VDP_TTXT_TYPE_MAN[1:0], Specify the Teletext Type,
Address 0x60 [1:0], User Sub Map
These bits specify the teletext type to be decoded. These bits are
functional only if VDP_TTXT_TYPE_MAN_ENABLE is set to 1.
Rev. A | Page 53 of 112
Table 68. VDP_TTXT_TYPE_MAN Function
VDP_TTXT_
TYPE_MAN[1:0]
625/50 (PAL)
00 (default)
Teletext-ITU-BT.653-
625/50-A
01
Teletext-ITU-BT.653-
625/50-B (WST)
10
Teletext-ITU-BT.653-
625/50-C
525/60 (NTSC)
Reserved
Teletext-ITU-BT.653-
525/60-B
Teletext-ITU-BT.653-
525/60-C or EIA516
(NABTS)
Teletext-ITU-BT.653-
525/60-D
11
Teletext-ITU-BT.653-
625/50-D
VDP Ancillary Data Output
Reading the data back via I
2
C may not be feasible for VBI data
standards with high data rates (for example, teletext). An
alternative is to place the sliced data in a packet in the line
blanking of the digital output CCIR656 stream. This is available
for all standards sliced by the VDP module.
When data has been sliced on a given line, the corresponding
ancillary data packet is placed immediately after the next EAV
code that occurs at the output (that is, data sliced from multiple
lines are not buffered up and then emitted in a burst). Note that,
due to the vertical delay through the comb filters, the line
number on which the packet is placed differs from the line
number on which the data was sliced.
The user can enable or disable the insertion of VDP decoded
results into the 656 ancillary streams by using the
ADF_ENABLE bit.
ADF_ENABLE, Enable Ancillary Data Output Through
656 Stream, Address 0x62 [7], User Sub Map
0
(default)—Disables insertion of VBI decoded data into
ancillary 656 stream.
1—Enables insertion of VBI decoded data into ancillary 656
stream.
The user may select the data identification word (DID) and the
secondary data identification word (SDID) through
programming the ADF_DID[4:0] and ADF_SDID[5:0]
bits,
respectively, as explained in the following sections.
ADF_DID[4:0], User-Specified Data ID Word in Ancillary
Data, Address 0x62 [4:0], User Sub Map
This bit selects the data ID word to be inserted into the
ancillary data stream with the data decoded by the VDP.
The default value of ADF_DID[4:0] is 10101.
ADF_SDID[5:0], User-Specified Secondary Data ID Word
in Ancillary Data, Address 0x63 [5:0], User Sub Map
These bits select the secondary data ID word to be inserted in
the ancillary data stream with the data decoded by the VDP.
The default value of ADF_SDID[5:0] is 101010.
DUPLICATE_ADF, Enable Duplication/Spreading of
Ancillary Data over Y and C Buses, Address 0x63 [7], User
Sub Map
This bit determines whether the ancillary data is duplicated
over both Y and C buses or if the data packets are spread
between the two channels.
0
(default)—The ancillary data packet is spread across the Y and
C data streams.
1—The ancillary data packet is duplicated on the Y and C data
streams.
ADF_MODE[1:0], Determine the Ancillary Data Output
Mode, Address 0x62 [6:5], User Sub Map
These bits determine if the ancillary data output mode is in byte
mode or nibble mode.
Table 69.
ADF_MODE[1:0]
00 (default)
01
10
Description
Nibble mode
Byte mode, no code restrictions
Byte mode, but 0x00 and 0xFF prevented
(0x00 replaced by 0x01, 0xFF replaced by
0xFE)
Reserved
11
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7181 | Multiformat SDTV Video Decoder |
| ADV7181B | Multiformat SDTV Video Decoder |
| ADV7181BBCPZ | Multiformat SDTV Video Decoder |
| ADV7181BBSTZ | Multiformat SDTV Video Decoder |
| ADV7181BCP | Multiformat SDTV Video Decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7180BSTZ | 制造商:Analog Devices 功能描述:Video IC |
| ADV7180BSTZ-REEL | 功能描述:IC VIDEO DECODER SDTV 64-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
| ADV7180KCP32Z | 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| ADV7180KCP32Z-RL | 功能描述:IC VIDEO DECODER 10BIT 32LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| ADV7180KST48Z | 功能描述:IC VID DECOD SDTV 10BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
發布緊急采購，3分鐘左右您將得到回復。