- 您現在的位置：買賣IC網 > PDF目錄67358 > ADT7476ARQZ-REEL7 (ANALOG DEVICES INC) DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADT7476ARQZ-REEL7 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| 封裝： | ROHS COMPLIANT, MO-137AE, QSOP-24 |
| 文件頁數： | 6/72頁 |
| 文件大?。?/td> | 5219K |
| 代理商： | ADT7476ARQZ-REEL7 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
ADT7476
Rev. B | Page 14 of 72
4.
When all data bytes have been read or written, stop
conditions are established. In write mode, the master pulls
the data line high during the 10th clock pulse to assert a
stop condition.
In read mode, the master device overrides the acknowledge
bit by pulling the data line high during the low period before
the ninth clock pulse. This is known as No Acknowledge.
The master then takes the data line low during the low
period before the 10th clock pulse, and then high during the
10th clock pulse to assert a stop condition. Any number of
bytes of data can be transferred over the serial bus in one
operation. It is not possible to mix read and write in one
operation because the type of operation is determined at the
beginning and cannot subsequently be changed without
starting a new operation. For the ADT7476, read operations
contain one byte, and write operations contain either one or
two bytes.
To write data to one of the device data registers or read
data from it, the address pointer register must be set so that
the correct data register is addressed; then data can be
written into that register or read from it. The first byte of a
write operation always contains an address stored in the
address pointer register. If data is to be written to the
device, the write operation contains a second data byte that
is written to the register selected by the address pointer
register (see Figure 18).
The device address is sent over the bus followed by the
R/W bit set to 0. This is followed by two data bytes. The
first data byte is the address of the internal data register to
be written to, which is stored in the address pointer
register. The second data byte is the data to be written to
the internal data register.
On PCs and servers, control of the ADT7476 is carried out
using the SMBus. The ADT7476 is connected to this bus as a
slave device, under the control of a master controller, which is
usually (but not necessarily) the ICH.
The ADT7476 has three 7-bit serial bus addresses. The R/W bit
must be added to get the 8-bit address (that is, 01011100 or
0x5C). Data is sent over the serial bus in sequences of nine
clock pulses: eight bits of data followed by an acknowledge bit
from the slave device. Transitions on the data line must occur
during the low period of the clock signal and remain stable
during the high period because a low-to-high transition when
the clock is high might be interpreted as a stop signal. The
number of data bytes transmitted over the serial bus in a single
read or write operation is limited only by what the master and
slave devices can handle.
When reading data from a register, there are two possibilities:
If the ADT7476 address pointer register value is unknown,
or not the desired value, it must first be set to the correct
value before data can be read from the desired data register.
This is done by performing a write to the ADT7476 as
before, but only the data byte containing the register
address is sent because no data is written to the register
(see Figure 19). A read operation is then performed
consisting of the serial bus address, R/W bit set to 1,
followed by the data byte read from the data register (see
If the address pointer register is already at the desired
address, data can be read from the corresponding data
register without first writing to the address pointer register
(see Figure 20).
R/W
0
SCL
SDA
10
1
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
ACK. BY
ADT7476
START BY
MASTER
19
1
ACK. BY
ADT7476
9
D7
D6
D5
D4
D3
D2
D1
D0
ACK. BY
ADT7476
STOP BY
MASTER
1
9
SCL (CONTINUED)
SDA (CONTINUED)
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
FRAME 3
DATA BYTE
05382-019
Figure 18. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7482ARMZ-RL | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7482ARMZ-U2 | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ-REEL | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
| ADT7485ARMZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7476EBZEVB | 功能描述:BOARD EVALUATION FOR ADT7476 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:dBCool® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADT7481 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm |
| ADT7481ARMZ | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-001 | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7481ARMZ-1 | 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。