參數資料
型號： ADT7476ARQZ-REEL7
廠商： ANALOG DEVICES INC
元件分類： 溫度/濕度傳感器
英文描述： DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT
封裝： ROHS COMPLIANT, MO-137AE, QSOP-24
文件頁數： 52/72頁
文件大?。?/td> 5219K
代理商： ADT7476ARQZ-REEL7
ADT7476
Rev. B | Page 56 of 72
Address R/W Description
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Default Lockable
0x7D
R/W
Configuration
Register 4
BpAtt
12 V
BpAtt
5 V
BpAtt VCCP
BpAtt
2.5 V
Max/Speed
on THERM
THERM
Disable
Pin14Func
0x00
Yes
0x7E
R
Test 1
Do not write to these registers
0x00
Yes
0x7F
R
Test 2
Do not write to these registers
0x00
Yes
Table 19. Register 0x10—Configuration Register 6 (Power-On Default = 0x00)1, 2
Bit
Name
R/W
Description
[0]
SlowFan
Remote 1
R/W
When this bit is set, Fan 1 smoothing times are multiplied ×4 for Remote 1 temperature channel (as defined
in Register 0x62).
[1]
SlowFan Local
R/W
When this bit is set, Fan 2 smoothing times are multiplied ×4 for local temperature channel (as defined in
Register 0x63).
[2]
SlowFan
Remote 2
R/W
When this bit is set, Fan 3 smoothing times are multiplied ×4 for Remote 2 temperature channel (as defined
in Register 0x63).
[3]
THERM in
Manual
R/W
When this bit is set, THERM is enabled in manual mode.1
[4]
SlaveEn
R/W
Setting this bit configures the ADT7476 as a slave for use in fan sync mode.
[5]
MasterEn
R/W
Setting this bit configures the ADT7476 as a master for use in fan sync mode.
[6]
VCCP Low
R/W
VCCP Low = 1. When the power is supplied from 3.3 V STANDBY and the core voltage (VCCP) drops below its
VCCP Low limit value (Register 0x46), the following occurs:
Status Bit 1 in Status Register 1 is set.
SMBALERT is generated, if enabled.
PROCHOT monitoring is disabled.
Everything is re-enabled once VCCP increases above the VCCP low limit.
When VCCP increases above the low limit:
PROCHOT monitoring is enabled.
Fans return to their programmed state after a spin-up cycle.
[7]
ExtraSlow
R/W
When this bit is set, all fan smoothing times are increased by an additional 39.2%
1 A THERM event always overrides any fan setting (even when fans are disabled).
2 This register becomes read-only when the Configuration Register 1 LOCK bit is set to 1. Any subsequent attempts to write to this register fail.
Table 20. Register 0x11—Configuration Register 7 (Power-On Default = 0x00)1
Bit
Name
R/W
Description
[0]
DisTHERMHys
R/W
Setting this bit to 1 disables THERM hysteresis.
[7:1]
Reserved
N/A
Reserved. Do not write to these bits.
1 This register becomes read-only when the Configuration Register 1 LOCK bit is set to 1. Any subsequent attempts to write to this register fail.
Table 21. Voltage Reading Registers (Power-On Default = 0x00)1
Register Address
R/W
Description
0x20
Read-only
Reflects the voltage measurement at the 2.5 V input on Pin 22 (8 MSBs of reading).
0x21
Read-only
Reflects the voltage measurement at the VCCP input on Pin 23 (8 MSBs of reading).2
0x22
Read-only
Reflects the voltage measurement at the VCC input on Pin 4 (8 MSBs of reading).3
0x23
Read-only
Reflects the voltage measurement at the 5 V input on Pin 20 (8 MSBs of reading).
0x24
Read-only
Reflects the voltage measurement at the 12 V input on Pin 21 (8 MSBs of reading).
1 If the extended resolution bits of these readings are also being read, the extended resolution registers (0x76, 0x77) must be read first. Once the extended resolution
registers have been read, the associated MSB reading registers are frozen until read. Both the extended resolution registers and the MSB registers are frozen.
2 If VCCP Low (Bit 7 of Register 0x40) is set, VCCP can control the sleep state of the ADT7476.
3 VCC (Pin 4) is the supply voltage for the ADT7476.
相關PDF資料
PDF描述
ADT7482ARMZ-RL DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT
ADT7482ARMZ-U2 DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT
ADT7485ARMZ-REEL DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT
ADT7485ARMZ DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT
ADT7485ARMZ-REEL7 DIGITAL TEMP SENSOR-SERIAL, 16BIT(s), 1Cel, SQUARE, SURFACE MOUNT
相關代理商/技術參數
參數描述
ADT7476EBZEVB 功能描述:BOARD EVALUATION FOR ADT7476 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:dBCool® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
ADT7481 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm
ADT7481ARMZ 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADT7481ARMZ-001 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADT7481ARMZ-1 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*