- 您現在的位置：買賣IC網 > PDF目錄67358 > ADT7470ARQZ (ANALOG DEVICES INC) DIGITAL TEMP SENSOR-SERIAL, 7BIT(s), RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADT7470ARQZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 7BIT(s), RECTANGULAR, SURFACE MOUNT |
| 封裝： | ROHS COMPLIANT, MO-137AB, QSOP-16 |
| 文件頁數： | 16/40頁 |
| 文件大小： | 962K |
| 代理商： | ADT7470ARQZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADT7470
Rev. C | Page 23 of
40
FAN SPEED MEASUREMENT
The fan counter does not count the fan tach output pulses
directly, because the fan speed may be less than 1000 RPM, and
it would take several seconds to accumulate a reasonably large
and accurate count. Instead, the period of the fan revolution is
measured by gating an on-chip 90 kHz oscillator into the input
of a 16-bit counter for N periods of the fan tach output, as shown
in Figure 24, so the accumulated count is actually proportional
to the fan tachometer period and inversely proportional to the
fan speed.
N, the number of pulses counted, is determined by the settings
of Register 0x43 (fan pulses per revolution register). This register
contains two bits for each fan, allowing 1, 2 (default), 3, or 4
tach pulses to be counted.
CLOCK
PWM
TACH
1
2
3
4
04684-
0-
029
Figure 24. Fan Speed Measurement
Fan Speed Measurement Registers
The fan tachometer readings are 16-bit values consisting of
a 2-byte read from the ADT7470.
Table 19. Fan Speed Measurement Registers
Register Address
Description
Default
0x2A
Tach 1 low byte
0x00
0x2B
Tach 1 high byte
0x00
0x2C
Tach 2 low byte
0x00
0x2D
Tach 2 high byte
0x00
0x2E
Tach 3 low byte
0x00
0x2F
Tach 3 high byte
0x00
0x30
Tach 4 low byte
0x00
0x31
Tach 4 high byte
0x00
Reading Fan Speed from the ADT7470
Measuring fan speed involves a 2-register read for each meas-
urement. The low byte should be read first. This causes the
high byte to be frozen until both high and low byte registers
are read from, preventing erroneous tach readings.
The fan tachometer reading registers report back the number
of 11.11 ms period clocks (90 kHz oscillator) gated to the fan
speed counter, from the rising edge of the first fan tach pulse
to the rising edge of the third fan tach pulse (assuming 2 pulses
per revolution are being counted). Since the device is essentially
measuring the fan tach period, the higher the count value,
the slower the fan is actually running. A 16-bit fan tachometer
reading of 0xFFFF indicates either that the fan has stalled or
is running very slowly (<100 RPM).
Fan Tach Limit Registers
The fan tach limit registers are 16-bit values consisting of two
bytes. Minimum limits determine fan under speed settings,
while maximum limits determine fan over speed settings.
Table 20. Fan Tach Limit Registers
Register Address
Description
Default
0x58
Tach 1 min low byte
0xFF
0x59
Tach 1 min high byte
0xFF
0x5A
Tach 2 min low byte
0xFF
0x5B
Tach 2 min high byte
0xFF
0x5C
Tach 3 min low byte
0xFF
0x5D
Tach 3 min high byte
0xFF
0x5E
Tach 4 min low byte
0xFF
0x5F
Tach 4 min high byte
0xFF
0x60
Tach 1 max low byte
0x00
0x61
Tach 1 max high byte
0x00
0x62
Tach 2 max low byte
0x00
0x63
Tach 2 max high byte
0x00
0x64
Tach 3 max low byte
0x00
0x65
Tach 3 max high byte
0x00
0x66
Tach 4 max low byte
0x00
0x67
Tach 4 max high byte
0x00
High Limit: Comparison
Because the actual fan tach period is being measured, exceeding
a fan tach limit by 1 sets the appropriate status bit and can be
used to generate an SMBALERT.
Fan Speed Measurement Rate
The fan tach readings are updated once every second by default.
The fast tach bit (Register 0x40 Bit[5]) controls the frequency
of tach measurements. Setting this bit to 1 increases the tach
measurements from one per second, to one every 250 ms.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7473ARQZ-1REEL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7473ARQZ-1REEL | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7476ARQZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7482ARMZ-RL | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7482ARMZ-U2 | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7470ARQZ-REEL | 功能描述:IC SENSOR TEMP FAN CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓撲:ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| ADT7470ARQZ-REEL7 | 功能描述:IC SENSOR TEMP FAN CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓撲:ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| ADT7473 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dbCOOL Remote Thermal Monitor and Fan Control |
| ADT7473_11 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dbCOOL Remote Thermal Monitor and Fan Control |
| ADT7473ARQZ | 功能描述:板上安裝溫度傳感器 THERMAL MONITOR FAN CONTROLLER RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。