- 您現在的位置：買賣IC網 > PDF目錄67358 > ADT7470ARQZ (ANALOG DEVICES INC) DIGITAL TEMP SENSOR-SERIAL, 7BIT(s), RECTANGULAR, SURFACE MOUNT PDF資料下載
參數資料
| 型號： | ADT7470ARQZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 7BIT(s), RECTANGULAR, SURFACE MOUNT |
| 封裝： | ROHS COMPLIANT, MO-137AB, QSOP-16 |
| 文件頁數： | 15/40頁 |
| 文件大?。?/td> | 962K |
| 代理商： | ADT7470ARQZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADT7470
Rev. C | Page 22 of
40
FAN SPEED MEASUREMENT
TACH INPUTS
Pin 6, Pin 7, Pin 4, and Pin 9 are open-drain tach inputs
intended for fan speed measurement.
Signal conditioning in the ADT7470 accommodates the slow
rise and fall times typical of fan tachometer outputs. The maxi-
mum input signal range is 0 V to 5 V, even where VCC is less
than 5 V. If these inputs are supplied from fan outputs that
exceed 0 V to 5 V, either resistive attenuation of the fan signal
or diode clamping must be included to keep inputs within an
common fan tach outputs.
If the fan tach output has a resistive pull-up to VCC, it can be
connected directly to the fan input, as shown in Figure 20.
12V
FAN SPEED
COUNTER
TACH
PULLUP
4.7k
Ω
TYP
TACH
OUTPUT
VCC
ADT7470
04684-
0-
025
Figure 20. Fan with Tach Pull-Up to VCC
If the fan output has a resistive pull-up to 12 V (or other voltage
greater than 5 V), the fan output can be clamped with a Zener
diode, as shown in Figure 21. The Zener diode voltage should
be chosen so that it is greater than VIH of the tach input but less
than 5 V, allowing for the voltage tolerance of the Zener. A value
of between 3 V and 5 V is suitable.
12V
FAN SPEED
COUNTER
TACH
OUTPUT
ZD1*
ZENER
PULLUP
4.7k
Ω
TYP
*CHOOSE ZD1 VOLTAGE APPROX. 0.8
× V
CC
VCC
ADT7470
04684-0-026
Figure 21. Fan with Tach.
Pull-Up to voltage > 5 V, for example, 12 V clamped with Zener diode.
If the fan output has a resistive pull-up to 12 V (or other voltage
greater than 5 V), the fan output can be clamped with a Zener
diode, as shown in Figure 21. The Zener diode voltage should
be chosen so that it is greater than VIH of the tach input but less
than 5 V, allowing for the voltage tolerance of the Zener. A value
of between 3 V and 5 V is suitable.
If the fan has a strong pull-up (less than 1 kΩ) to 12 V, or a
totem-pole output, a series resistor can be added to limit the
Zener current, as shown in Figure 22. Alternatively, a resistive
attenuator can be used, as shown in Figure 23.
R1 and R2 should be chosen such that
2 V < VPULL-UP × R2/(RPULL-UP + R1 + R2) < 5 V
The fan inputs have an input resistance of nominally 160 kΩ to
ground, which should be taken into account when calculating
resistor values.
With a pull-up voltage of 12 V and pull-up resistor less than
1 kΩ, suitable values for R1 and R2 are 100 kΩ and 47 kΩ.
This gives a high input voltage of 3.83 V.
12V
FAN SPEED
COUNTER
TACH
PULLUP
TYP. <1k
Ω
OR TOTEM-POLE
ZD1
ZENER*
R1
10k
Ω
TACH
O/P
*CHOOSE ZD1 VOLTAGE APPROX. 0.8
× V
CC
VCC
ADT7470
04684-0-027
Figure 22. Fan with Strong Tach.
Pull-Up to > VCC or Totem-Pole Output, Clamped with Zener and Resistor.
12V
FAN SPEED
COUNTER
TACH
OUTPUT
R1*
R2*
<1k
Ω
VCC
*SEE TEXT
ADT7470
04684-0-028
Figure 23. Fan with Strong Tach.
Pull-Up to > VCC or Totem-Pole Output, Attenuated with R1/R2.
Pulse Stretching
Pulse stretching of the PWM output is performed automatically
in low frequency fan drive mode, to ensure that sufficient tach
readings are taken from the fan.
However, in high frequency fan drive mode, pulse stretching is
disabled. If using 3-wire fans this mode, care should be taken to
ensure that incomplete tach information does not occur at low
PWM duty cycles, or short PWM pulse widths.
Disabling Tach measurement
The tach measurement for each fan can be disabled by writing
to Configuration Register 2 Bits[3:0], at Address 0x74.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7473ARQZ-1REEL7 | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7473ARQZ-1REEL | DIGITAL TEMP SENSOR-SERIAL, 8BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7476ARQZ-REEL7 | DIGITAL TEMP SENSOR-SERIAL, 10BIT(s), 2.50Cel, RECTANGULAR, SURFACE MOUNT |
| ADT7482ARMZ-RL | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
| ADT7482ARMZ-U2 | DIGITAL TEMP SENSOR-SERIAL, 11BIT(s), 2.5Cel, SQUARE, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7470ARQZ-REEL | 功能描述:IC SENSOR TEMP FAN CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| ADT7470ARQZ-REEL7 | 功能描述:IC SENSOR TEMP FAN CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:2,500 系列:SilentSense™ 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-55°C ~ 125°C，外部傳感器 精確度:±2°C 本地（最大），±3°C 遠程（最大） 拓?fù)?ADC（三角積分型），比較器，寄存器庫 輸出類型:I²C?/SMBus? 輸出警報:是 輸出風扇:是 電源電壓:2.7 V ~ 5.5 V 工作溫度:-55°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) 其它名稱:MIC284-2BMMTRMIC284-2BMMTR-ND |
| ADT7473 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dbCOOL Remote Thermal Monitor and Fan Control |
| ADT7473_11 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:dbCOOL Remote Thermal Monitor and Fan Control |
| ADT7473ARQZ | 功能描述:板上安裝溫度傳感器 THERMAL MONITOR FAN CONTROLLER RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。