參數資料
型號： ADS1194CZXGT
廠商： TEXAS INSTRUMENTS INC
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PBGA64
封裝： 8 X 8 MM, GREEN, PLASTIC, NFBGA-64
文件頁數： 53/76頁
文件大?。?/td> 1193K
代理商： ADS1194CZXGT
a)LOFF_FLIP=0
a)LOFF_FLIP=1
PGA
10MW
AVDD
INP
INN
PGA
10MW
AVDD
INP
INN
ADS119x
a)Pull-Up/Pull-DownResistors
b)CurrentSource
PGA
10MW
AVDD
INP
INN
PGA
AVDD
INP
INN
ADS119x
SBAS471B
– APRIL 2010 – REVISED APRIL 2011
DC Lead-Off
In this method, the lead-off excitation is with a dc signal. The dc excitation signal can be chosen from either a
pull-up/pull-down resistor or a current source/sink, shown in Figure 47. The selection is done by setting the
VLEAD_OFF_EN bit in the LOFF register. One side of the channel is pulled to supply and the other side is pulled
to ground. The pull-up resistor and pull-down resistor can be swapped (as shown in Figure 48) by setting the bits
in the LOFF_FLIP register. In case of current source/sink, the magnitude of the current can be set by using the
ILEAD_OFF[1:0] bits in the LOFF register. The current source/sink gives larger input impedance compared to the
10M
pull-up/pull-down resistor.
Figure 47. DC Lead-Off Excitation Options
Figure 48. LOFF_FLIP Usage
Sensing of the response can be done either by looking at the digital output code from the device or by monitoring
the input voltages with an on-chip comparator. If either of the electrodes is off, the pull-up resistors and/or the
pull-down resistors saturate the channel. By looking at the output code it can be determined that either the P-side
or the N-side is off. To pinpoint which one is off, the comparators must be used. The input voltage is also
monitored using a comparator and a 4-bit DAC whose levels are set by the COMP_TH[2:0] bits in the LOFF
register. The output of the comparators are stored in the LOFF_STATP and LOFF_STATN registers. These two
registers are available as a part of the output data stream. (See the Data Output (DOUT) subsection of the SPI
Interface section.) If dc lead-off is not used, the lead-off comparators can be powered down by setting the
PD_LOFF_COMP bit in the CONFIG4 register.
An example procedure to turn on dc lead-off is given in the Lead-Off subsection of the Quick-Start Guide section.
Copyright
2010–2011, Texas Instruments Incorporated
57
Product Folder Link(s): ADS1194 ADS1196 ADS1198
相關PDF資料
PDF描述
ADS1251 "ResolutionPlus 24-Bit
ADS5102IPFBR 1.8-V ANALOG SUPPLY, 10-BIT, 65/40 MSPS ANALOG-TO-DIGITAL CONVERTERS WITH INTERNAL REFERENCE
ADS5103 "10 Bit
ADS5103CPFB 1.8-V ANALOG SUPPLY, 10-BIT, 65/40 MSPS ANALOG-TO-DIGITAL CONVERTERS WITH INTERNAL REFERENCE
ADS5103CPFBR 1.8-V ANALOG SUPPLY, 10-BIT, 65/40 MSPS ANALOG-TO-DIGITAL CONVERTERS WITH INTERNAL REFERENCE
相關代理商/技術參數
參數描述
ADS1194IPAG 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Power 8-Channel 16-Bit Analog Front-End for Biopotential Measurements
ADS1194IPAGR 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Power 8-Channel 16-Bit Analog Front-End for Biopotential Measurements
ADS1196 制造商:TI 制造商全稱:Texas Instruments 功能描述:Low-Power, 8-Channel, 24-Bit Analog Front-End for Biopotential Measurements
ADS1196CPAG 功能描述:模數轉換器 - ADC Low-Pwr6Ch16B Ana Front-End for ECG RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
ADS1196CPAG 制造商:Texas Instruments 功能描述:; Resolution (Bits):16bit; Sampling Rate 制造商:Texas Instruments 功能描述:IC, ADC, 6CH, 16BIT, 8KSPS, TQFP-64
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*