參數資料
型號： ADM1029ARQZ-R7
廠商： ON Semiconductor
文件頁數： 16/50頁
文件大?。?/td> 402K
描述： IC SENSOR 2TEMP/FAN CTRL 24QSOP
產品變化通告： QSOP 24ld Pkg (MSL) Change 17/Jun/2010
標準包裝： 1,000
功能： 風扇控制，溫度監控器
傳感器類型： 內部和外部
感應溫度： 0°C ~ 100°C，外部傳感器
精確度： ±1°C 本地，±3°C 遠程
拓?fù)洌?/td> ADC，風扇控制，寄存器庫
輸出類型： 開路漏極
輸出警報： 是
輸出風扇： 是
電源電壓： 3 V ~ 5.5 V
工作溫度： 0°C ~ 100°C
安裝類型： 表面貼裝
封裝/外殼： 24-SSOP（0.154"，3.90mm 寬）
供應商設備封裝： 24-QSOP
包裝： 帶卷 (TR)
ADM1029
http://onsemi.com
16
Figure 27. Fan with Strong Tach. Pull-up to > V
CC
 or
Totem-pole Output, Clamped with Zener and Resistor
12 V
V
CC
FAN SPEED
COUNTER
TACH
OUTPUT
TACH1
OR
TACH 2
PULL-UP
TYP < 1 kW
OR TOTEM-POLE
ZD1*
ZENER
* Choose ZD1 Voltage Approx. 0.8 ?V
CC
R1
10 kW
Figure 28. Fan with Strong Tach. Pull-up to > V
CC
 or
Totem-pole Output, Attenuated with R1/R2
12 V
V
CC
FAN SPEED
COUNTER
TACH
OUTPUT
TACH1
OR
TACH 2
< 1 kW
R2*
*
See
 
Text
R1*
Fan Speed Control
Fan speed is controlled using pulsewidth modulation
(PWM). The PWM outputs (Pins 1 and 24) give a pulse
output with a programmable frequency (default 250 Hz) and
a duty-cycle defined by the contents of the relevant fan speed
register, or by the automatic fan speed control when this
mode is enabled. The speed at which a fan runs is determined
by fault conditions and the settings of various control and
mask registers.
A fan can only be driven if it is defined as being supported
by the controller in register 02h. The ADM1029 supports up
to two fans, so Bits 0 and 1 of this register are permanently
set. This register is read-only.
A fan will only be driven if it is defined as being supported
by the system in register 03h. If Bit 0 of this register is set,
it indicates that Fan 1 is installed. This is the power-on
default. If Bit 1 is set, it indicates that Fan 2 is installed. This
bit is set by the state of Pin 18 at power-up. This register is
read/write and the default/power-on setting can be
overwritten. If a fan is not supported in register 03h it will
not be driven, even if it is physically installed.
The PWM outputs are open-drain outputs. They require
pull-up resistors and must be amplified and buffered to drive
the fans.
Minimum Speed
The normal operating fan speed is set by the four LSBs of
the Fan 1 and Fan 2 Minimum/Alarm Speed Registers
(addresses 60h, 61h). These bits also set the minimum speed
at which a fan will run in automatic control mode. These bits
should be set to 05h. This corresponds to 33% PWM
duty-cycle, which is the lowest speed at which most fans will
run reliably.
Fan(s) will run at minimum speed if there is no fault
condition, automatic fan speed is disabled, and there are no
other overriding conditions.
Alarm Speed
Alarm speed is set by the four MSBs of the Fan 1 and
Fan 2 Minimum/Alarm Speed Registers (addresses 60h,
61h). Fan(s) will run at alarm speed if any of the following
conditions occurs, assuming the condition has not been
masked out using the Fan Event Mask Registers:
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> Setting Bit 0 of register 07h forces Fan 1 to run at alarm
speed (Set Fan x Alarm Speed Register).
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> Setting Bit 1 of register 07h forces Fan 2 to run at alarm
speed (Set Fan x Alarm Speed Register).
If monitoring is disabled by clearing Bit 4 of the
Configuration Register, all fans controlled by the
ADM1029 will run at alarm speed.
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> When a GPIO pin is configured as an input by setting
Bit 0 of the corresponding GPIO Behavior Register,
and Bit 4 of the GPIO Behavior Register is also set, all
fans controlled by the ADM1029 will go to alarm speed
when the logic input is asserted (high or low, depending
on the polarity bit, Bit 1 of the corresponding GPIO
Behavior Register).
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> If Bit 7 of a Fan Fault Action Register is set 
(18h  Fan 1, 19h  Fan 2) the corresponding fan will
go to alarm speed when CFAULT
 is pulled low by an
external source.
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> If a tach measurement exceeds the set limit, all fans
controlled by the ADM1029 will run at alarm speed.
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> If a fan fault input pin is asserted (low), all fans
controlled by the ADM1029 will run at alarm speed.
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> If Bit 1 of a Temp. Fault Action Register is set 
(40h  Local Sensor, 41h  Remote 1, 42h  Remote 2),
all fans controlled by the ADM1029 will go to alarm
speed if the corresponding temperature high limit is
exceeded.
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> If Bit 5 of a Temp. Fault Action Register is set, all fans
controlled by the ADM1029 will go to alarm speed if a
temperature input crosses the corresponding
temperature low limit, the direction depending on the
setting of Bit 3 of the Temp. Control register.
(0 = alarm when input goes below low limit, 1 = alarm
when input goes above low limit).
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> If Bit 1 of an AIN Behavior Register is set 
(50h  AIN0, 51h  AIN1), all fans controlled by the
ADM1029 will go to alarm speed if the corresponding
AIN high limit is exceeded.
?SPAN class="pst ADM1029ARQZ-R7_2295375_7"> If Bit 5 of an AIN Behavior Register is set, all fans
controlled by the ADM1029 will go to alarm speed if
相關PDF資料
PDF描述
ADM1030ARQZ-RL7 IC SNSR TEMP/FAN PWM CTRL 16QSOP
ADM1032ARZ-REEL IC TEMP MONITOR 85DEG 8SOIC
ADM1033ARQZ-RL7 IC THERM/FAN SPEED CTLR 16-QSOP
ADM1034ARQZ-REEL IC THERM/FAN SPEED CTRLR 16-QSOP
ADN8810ACPZ-REEL7 IC CURRENT SOURCE(12BIT) 24LFCSP
相關代理商/技術參數
參數描述
ADM1030 制造商:AD 制造商全稱:Analog Devices 功能描述:Intelligent Temperature Monitor and PWM Fan Controller
ADM1030ARQ 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1030ARQ-REEL 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1030ARQ-REEL7 功能描述:IC SNSR TEMP/FAN PWM CTRL 16QSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6
ADM1030ARQZ 功能描述:馬達/運動/點火控制器和驅動器 TDM & PWM FAN CNTRLRS IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*