- 您現在的位置：買賣IC網 > PDF目錄8963 > AD9772AASTZ (Analog Devices Inc)IC DAC 14BIT 160MSPS 48-LQFP PDF資料下載
參數資料
| 型號： | AD9772AASTZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 26/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT 160MSPS 48-LQFP |
| 產品培訓模塊： | DAC Architectures |
| 標準包裝： | 1 |
| 系列： | TxDAC+® |
| 設置時間： | 11ns |
| 位數： | 14 |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 272mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 2 電流，單極；2 電流，雙極 |
| 采樣率（每秒）： | 160M |
| 產品目錄頁面： | 785 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
AD9772A
Rev. C | Page 32 of 40
AD9772A EVALUATION BOARD
The AD9772A-EB is an evaluation board for the AD9772A
TxDAC. Careful attention to the layout and circuit design,
along with the prototyping area, allows the user to easily and
effectively evaluate the AD9772A in different modes of operation.
Referring to Figure 60 and Figure 61, the performance of
AD9772A can be evaluated differentially or in a single-ended
fashion using a transformer, differential amplifier, or directly
coupled output. To evaluate the output differentially using the
transformer, remove Jumper JP12 and Jumper JP13 and
monitor the output at J6 (IOUT). To evaluate the output
differentially, remove the transformer (T2) and install jumpers
JP12 and JP13. The output of the amplifier can be evaluated at
J13 (AMPOUT). To evaluate the AD9772A in a single-ended
fashion with a directly coupled output, remove the transformer
and Jumper JP12 and Jumper JP13, and install Resistor R16 or
Resistor R17 with 0 Ω.
The digital data to the AD9772A comes across a ribbon cable
that interfaces to a 40-pin IDC connector. Proper termination
or voltage scaling can be accomplished by installing the RN2
and/or RN3 SIP resistor networks. The 22 Ω DIP resistor
network, RN1, must be installed and helps reduce the digital
data edge rates. A single-ended clock input can be supplied via
the ribbon cable by installing JP8, or, more preferably, via the
SMA connector, J3 (CLOCK). If the clock is supplied by J3, the
AD9772A can be configured for a differential clock interface by
installing Jumper JP1 and configuring JP2, JP3, and JP9 in the
DF position. To configure the AD9772A clock input for a
single-ended clock interface, remove JP1 and configure JP2,
JP3, and JP9 in the SE position.
The AD9772A PLL clock multiplier can be disabled by config-
uring Jumper JP5 in the L position. In this case, the user must
supply a clock input at twice (2×) the data rate via J3 (CLOCK).
The 1× clock is available on the SMA connector J1 (PLLLOCK),
and should be used to trigger a pattern generator directly or via
a programmable pulse generator. Note that PLLLOCK is capable
of providing a 0 V to 0.85 V output into a 50 Ω load. To enable
the PLL clock multiplier, JP5 must be configured for the
H position. In this case, the clock can be supplied via the ribbon
cable (that is, JP8 installed) or J3 (CLOCK). The divide-by-N
ratio can be set by configuring JP6 (DIV0) and JP7 (DIV1).
The AD9772A can be configured for baseband or direct IF
mode operation by configuring Jumper JP11 (MOD0) and
Jumper JP10 (MOD1). For baseband operation, JP10 and JP11
should be configured in the L position. For direct IF operation,
JP10 and JP11 should be configured in the H position. For direct
IF operation without zero-stuffing, JP11 should be configured in
the H position while JP10 should be configured in the low position.
The AD9772A voltage reference can be enabled or disabled via
JP4. To enable the reference, configure JP4 in the internal position.
A voltage of approximately 1.2 V will appear at the TP6 (REFIO)
test point. To disable the internal reference, configure JP4 in the
external position and drive TP6 with an external voltage reference.
Lastly, the AD9772A can be placed in the sleep mode by driving
the TP11 test point with a logic level high input signal.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3450L32-15P | CONN RCPT 8POS WALL MNT W/PINS |
| ADV7123JSTZ330 | IC DAC VIDEO 3CH 330MHZ 48-LQFP |
| MS27484T24B4P | CONN PLUG 56POS STRAIGHT W/PINS |
| VI-263-MW-S | CONVERTER MOD DC/DC 24V 100W |
| VI-263-MW-F4 | CONVERTER MOD DC/DC 24V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9772AASTZRL | 功能描述:IC DAC 14BIT 160MSPS 48LQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:TxDAC+® 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| AD9772A-EB | 制造商:Analog Devices 功能描述:14 BIT DAC W/2X INTERPOLATION 制造商:Analog Devices 功能描述:DEV TOOLS, EVAL BD FOR AD9772A - Bulk |
| AD9772A-EBZ | 功能描述:BOARD EVAL FOR AD9772A RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:TxDAC+® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9772AST | 制造商:Rochester Electronics LLC 功能描述:14 BIT DAC W/2X INTERPOLA - Tape and Reel |
| AD9772EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:14-Bit, 160 MSPS TxDAC+ with 2x Interpolation Filter |
發布緊急采購，3分鐘左右您將得到回復。