- 您現在的位置：買賣IC網 > PDF目錄10050 > AD9644CCPZ-80 (Analog Devices Inc)IC ADC 14BIT 80MSPS 3V 48LFCSP PDF資料下載
參數資料
| 型號： | AD9644CCPZ-80 |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 33/44頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 80MSPS 3V 48LFCSP |
| 標準包裝： | 1 |
| 位數： | 14 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 460mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-VFQFN 裸露焊盤，CSP |
| 供應商設備封裝： | 48-LFCSP-VQ（7x7） |
| 包裝： | 托盤 |
| 輸入數目和類型： | 2 個差分，雙極 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Data Sheet
AD9644
Rev. C | Page 39 of 44
JESD204A Link Control Register 1 (Register 0x60)
Bit 7—Reserved
Bit 6—Serial Tail Bit Enable
If this bit is set, the unused tail bits are padded with a pseudo
random number sequence from a 31-bit LFSR (see JESD204A
5.1.4).
Bit 5—Serial Test Sample Enable
If this bit is set, JESD204A test samples are enabled—transport
layer test sample sequence (as specified in JESD204A section
5.1.6.2) is sent on all link lanes.
Bit 4—Serial Lane Synchronization Enable
If this bit is set, lane synchronization is enabled. Both sides
perform lane sync. Frame alignment character insertion uses
either /K28.3/ or /K28.7/ control characters (see JESD204A
5.3.3.4).
Bits[3:2]—Serial Lane Alignment Sequence Mode
00: initial lane alignment sequence disabled.
01: initial lane alignment sequence enabled.
10: reserved.
11: initial lane alignment sequence always on test mode—
JESD204A data link layer test mode where repeated lane alignment
sequence is sent on all lanes.
Bit 1—Frame Alignment Character Insertion Disable
If Bit 1 is set, the frame alignment character insertion is
disabled per JESD204A section 5.3.3.4.
Bit 0—Serial Transmit Link Powered Down
If Bit 0 is set high, the serial transmit link is held in reset with its
clock gated off. The JESD204A transmitter should be powered
down when changing any of the link configuration bits.
JESD204A Link Control Register 2 (Register 0x61)
Bits[7:6]—Local DSYNC Mode
00: individual/separate mode. Each link is controlled by a
separate DSYNC pin that independently controls code group
synchronization.
01: global mode. Any DSYNC signal causes the link to begin
code group synchronization.
10: sync active mode. DSYNC signal is active—force code group
synchronization.
11: DSYNC pin disabled.
Bit 5—DSYNC Pin Input Inverted
If this bit is set, the DSYNC pin of the link is inverted (active high).
Bit 4—CMOS DSYNC Input
0: LVDS differential pair DSYNC input (default)
1: CMOS single ended DSYNC input
Bit 3—Open
Bit 2—Bypass 8b/10b Encoding
If this bit is set the 8b/10b encoding is bypassed and the most
significant bits are set to 0.
Bit 1—Invert Transmit Bits
Setting this bit inverts the 10 serial output bits. This effectively
inverts the output signals.
Bit 0—Mirror Serial Output Bits
Setting this bit reverses the order of the 10b outputs.
JESD204A Link Control Register 3 (Register 0x62)
Bit 7—Disable CHKSUM
Setting this bit high disables the CHKSUM configuration
parameter (for testing purposes only).
Bit 6—Open
Bits[5:4]—Link Test Generation Input Selection
00: 16-bit test generation data injected at sample input to
the link.
01: 10-bit test generation data injected at output of 8b/10b
encoder (at input to PHY).
10: reserved.
11: reserved.
Bit 3—Open
Bits[2:0]—Link Test Generation Mode
000: normal operation (test mode disabled).
001: alternating checker board.
010: 1/0 word toggle.
011: PN sequence—long.
100: PN sequence—short.
101: continuous/repeat user test mode—most significant bits
from user pattern (1, 2, 3, 4) placed on the output for 1 clock
cycle and then repeat. (output user pattern 1, 2, 3, 4, 1, 2, 3, 4, 1,
2, 3, 4…).
110: single user test mode—most significant bits from user
pattern (1, 2, 3, 4) placed on the output for 1 clock cycle and
then output all zeros. (output user pattern 1, 2, 3, 4, then output
all zeros).
111: ramp output.
JESD204A Link Control Register 4 (Register 0x63)
Bits[7:0]—Initial Lane Alignment Sequence Repeat Count
Specifies the number of times the initial lane alignment
sequence (ILAS) is repeated. If 0 is programmed the ILAS does
not repeat. If 1 is programmed the ILAS repeat one time and so
on. See Register 0x60, Bits[3:2] to enable the ILAS and for a test
mode to continuously enable the initial lane alignment
sequence.
相關PDF資料 |
PDF描述 |
|---|---|
| MS27508E10B98PA | CONN RCPT 6POS BOX MNT W/PINS |
| VE-26M-MX-F3 | CONVERTER MOD DC/DC 10V 75W |
| MS27484T16A8PA | CONN PLUG 8POS STRAIGHT W/PINS |
| IDT72V84L20PA | IC FIFO ASYNCH 2048X18 56TSSOP |
| MS3100R22-15P | CONN RCPT 6POS WALL MNT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD9644CCPZRL7-80 | 功能描述:IC ADC 14BIT 80MSPS 3V 48LFCSP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| AD9645 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual, 14-Bit, 80 MSPS/125 MSPS, Serial LVDS |
| AD9645-125EBZ | 功能描述:數據轉換 IC 開發工具 14Bit 125Msps Dual ADC w/serial LVDS RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| AD9645BCPZ-125 | 功能描述:模數轉換器 - ADC Dual 14-Bit 125 MSPS Serial LVDS 1.8V RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
| AD9645BCPZ-80 | 功能描述:模數轉換器 - ADC Dual 14-Bit 80 MSPS Serial LVDS 1.8V RoHS:否 制造商:Analog Devices 通道數量: 結構: 轉換速率: 分辨率: 輸入類型: 信噪比: 接口類型: 工作電源電壓: 最大工作溫度: 安裝風格: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。